manualshive.com logo in svg

Dodge 2008 Avenger, Owner'S Manual

The Dodge 2008 Avenger Owner's Manual is your go-to guide for getting the most out of your vehicle. This comprehensive manual covers everything from maintenance and troubleshooting to important safety information. Download your free copy from manualshive.com and enjoy the peace of mind that comes with knowing your vehicle inside out.

Share
Download
background image

3. There are two front jacking locations and two rear
jacking locations on each side of the body as shown.

CAUTION!

Do not attempt to raise the vehicle by jacking on
locations other than those indicated in step 3.

4. Turn the jack screw to the left until the jack can be
placed under the jacking location. Once the jack is
positioned, turn the jack screw to the right until the jack
head is properly engaged with the lift area closest to the
wheel to be changed. Do not raise the vehicle until you
are sure the jack is securely engaged.

WARNING!

Raising the vehicle higher than necessary can make
the vehicle less stable. It could slip off the jack and
hurt someone near it. Raise the vehicle only enough
to remove the tire.

5. Raise the vehicle by turning the jack screw to the right,
using the swivel wrench. Raise the vehicle only until the
tire just clears the surface and enough clearance is
obtained to install the spare tire. Minimum tire lift
provides maximum stability.

6. Remove the wheel nuts, and pull the wheel and wheel
covers (where applicable) off the hub. Install the spare
wheel and wheel nuts with the cone shaped end of the
nuts toward the wheel. Lightly tighten the nuts. To avoid
the risk of forcing the vehicle off the jack, do not tighten
the nuts fully until the vehicle has been lowered.

356

WHAT TO DO IN EMERGENCIES

Summary of Contents for 2008 Avenger




















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2008 Avenger

Oldsmobile 2004 Alero Owner'S Manual preview
2004 Alero
Brand: Oldsmobile Pages: 360
EUFAB 11556 Operating Instructions Manual preview
11556
Brand: EUFAB Pages: 52
Pyle PLDCP3 User Manual preview
PLDCP3
Brand: Pyle Pages: 2
Safe Fleet PRIME DESIGN VCR-TC11B Assembly Instructions Manual preview
PRIME DESIGN VCR-TC11B
Brand: Safe Fleet Pages: 12
Gentex ADVGEN20A Manual preview
ADVGEN20A
Brand: Gentex Pages: 2
iQOS CCU01 Safety Warnings And Instructions preview
CCU01
Brand: iQOS Pages: 4
Bracketron Multi Vehicle Mount MVM-35-05 Installation Manual preview
Multi Vehicle Mount MVM-35-05
Brand: Bracketron Pages: 4
Kargo Master 40983 Quick Start Manual preview
40983
Brand: Kargo Master Pages: 18
Yakima K1198 Instructions Manual preview
K1198
Brand: Yakima Pages: 10
Directed Directechs FORD11 Installation Manual preview
Directechs FORD11
Brand: Directed Pages: 23
Menabo 171071 Fitting Instructions preview
171071
Brand: Menabo Pages: 4
LetsGoAero V2 Two-Bike Carrier User Manual preview
V2 Two-Bike Carrier
Brand: LetsGoAero Pages: 2
Toyota 2009 Tacoma Quick Reference Manual preview
2009 Tacoma
Brand: Toyota Pages: 22
SoundMax SM-DVR77FHD Instruction Manual preview
SM-DVR77FHD
Brand: SoundMax Pages: 20
RADICAL R-C10-DAB Installation Manual preview
R-C10-DAB
Brand: RADICAL Pages: 4
SAF-HOLLAND DB-1400 Owner'S Manual preview
DB-1400
Brand: SAF-HOLLAND Pages: 12
ikross IKHD74 User Manual preview
IKHD74
Brand: ikross Pages: 2
MSD Ignition 2351 Installation Instructions preview
2351
Brand: MSD Ignition Pages: 4

Brands by name

Popular brands

Load more brands