manualshive.com logo in svg

Dodge 2008 Avenger, Owner'S Manual

The Dodge 2008 Avenger Owner's Manual is your go-to guide for getting the most out of your vehicle. This comprehensive manual covers everything from maintenance and troubleshooting to important safety information. Download your free copy from manualshive.com and enjoy the peace of mind that comes with knowing your vehicle inside out.

Share
Download
background image

The operator can override the AUTO mode setting to
change airflow distribution by rotating the Mode Control
knob (on the right) to one of the following positions.

•

Panel

Air is directed through the outlets in the instru-
ment panel. These outlets can be adjusted to

direct airflow.

NOTE:

The center instrument panel outlets can be

aimed so that they are directed toward the rear seat
passengers for maximum airflow to the rear.

•

Bi-Level

Air is directed through the panel and floor out-
lets.

NOTE:

For all settings except full cold or full hot, there

is a difference in temperature between the upper and
lower outlets. The warmer air flows to the floor outlets.
This feature gives improved comfort during sunny but
cool conditions.

•

Floor

Air is directed through the floor outlets with a
small amount flowing through the defrost and

side window demist outlets.

•

Mix

Air is directed through the floor, defrost, and
side window demist outlets. This setting works
best in cold or snowy conditions that require

extra heat to the windshield. This setting is good for
maintaining comfort while reducing moisture on the
windshield.

250

UNDERSTANDING YOUR INSTRUMENT PANEL

Summary of Contents for 2008 Avenger




















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2008 Avenger

KC HiLiTES C Series Wiring Diagram preview
C Series
Brand: KC HiLiTES Pages: 4
A-Tach Mounts ST-1 Instructions preview
ST-1
Brand: A-Tach Mounts Pages: 2
A-Tach Mounts 50291 Quick Start Manual preview
50291
Brand: A-Tach Mounts Pages: 2
A-Tach Mounts 50206 Instructions preview
50206
Brand: A-Tach Mounts Pages: 2
Tesla V2 SUPERCHARGER First Responder'S Manual preview
V2 SUPERCHARGER
Brand: Tesla Pages: 9
Suzuki Movano Owner'S Manual preview
Movano
Brand: Suzuki Pages: 353
Torklift F2012 Installation Instructions Manual preview
F2012
Brand: Torklift Pages: 16
CITROEN PICASSO XSARA DESIRE 1.6 - MESUREMENT Manual preview
PICASSO XSARA DESIRE 1.6 - MESUREMENT
Brand: CITROEN Pages: 2
BrandMotion 1009-6503 Installation Instructions Manual preview
1009-6503
Brand: BrandMotion Pages: 8
Victory 4x4 UNI-UPRS Install Instructions Manual preview
UNI-UPRS
Brand: Victory 4x4 Pages: 13
Atwood Lippert Components LEVELEGS MPD 66385 Manual preview
Lippert Components LEVELEGS MPD 66385
Brand: Atwood Pages: 6
BMW 65 41 2 152 528 Installation Instructions Manual preview
65 41 2 152 528
Brand: BMW Pages: 21
Caltrend CV445 Installation Instructions preview
CV445
Brand: Caltrend Pages: 2
Audiovox EM-2201 Installation Instructions preview
EM-2201
Brand: Audiovox Pages: 1
EGR EGR-3PVE-COLOUR Installation Instructions Manual preview
EGR-3PVE-COLOUR
Brand: EGR Pages: 28
Xblitz Mirror 2016 User Manual preview
Mirror 2016
Brand: Xblitz Pages: 30
Simplicity 1694286 Installation Instructions Manual preview
1694286
Brand: Simplicity Pages: 10
Valeo Park Vision VAL632210 Instruction Manual preview
Park Vision VAL632210
Brand: Valeo Pages: 25

Brands by name

Popular brands

Load more brands