manualshive.com logo in svg

Dodge 2008 Avenger, Owner'S Manual

The Dodge 2008 Avenger Owner's Manual is your go-to guide for getting the most out of your vehicle. This comprehensive manual covers everything from maintenance and troubleshooting to important safety information. Download your free copy from manualshive.com and enjoy the peace of mind that comes with knowing your vehicle inside out.

Share
Download
background image

TIRE SAFETY INFORMATION

Tire Markings

NOTE:

•

P (Passenger) - Metric tire sizing is based on U.S.
design standards. P-Metric tires have the letter “P”
molded into the sidewall preceding the size designa-
tion. Example: P215/65R15 95H.

•

European-Metric tire sizing is based on European
design standards. Tires designed to this standard have
the tire size molded into the sidewall beginning with
the section width. The letter

9

P

9

is absent from this tire

size designation. Example: 215/65R15 96H.

•

LT (Light Truck) - Metric tire sizing is based on U.S.
design standards. The size designation for LT-Metric
tires is the same as for P-Metric tires except for the
letters “LT” that are molded into the sidewall preced-
ing the size designation. Example: LT235/85R16.

•

Temporary spare tires are high-pressure compact
spares designed for temporary emergency use only.
Tires designed to this standard have the letter “T”
molded into the sidewall preceding the size designa-
tion. Example: T145/80D18 103M.

•

High flotation tire sizing is based on U.S. design
standards, and it begins with the tire diameter molded
into the sidewall. Example: 31x10.5 R15 LT.

STARTING AND OPERATING

291

5

Summary of Contents for 2008 Avenger




















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2008 Avenger

Daewoo RACER 1998 Electrical Wiring Diagram preview
RACER 1998
Brand: Daewoo Pages: 68
Hyundai Getz 2004 Owner'S Manual preview
Getz 2004
Brand: Hyundai Pages: 437
Pontiac 2004 Vibe Navigation System Owner'S Manual preview
2004 Vibe Navigation System
Brand: Pontiac Pages: 44
Renault 2016 Sandero Stepway Handbook preview
2016 Sandero Stepway
Brand: Renault Pages: 183
Connects2 adaptiv mini ADVM-BM1 Fitting & User Manual preview
adaptiv mini ADVM-BM1
Brand: Connects2 Pages: 4
SAN HIMA SH-TENT-SY20 User Manual preview
SH-TENT-SY20
Brand: SAN HIMA Pages: 7
Paccar Peterbilt SmartAir Operator'S Manual preview
Peterbilt SmartAir
Brand: Paccar Pages: 58
Mercedes-Benz 300 SL Operator'S Manual preview
300 SL
Brand: Mercedes-Benz Pages: 153
Parkeon StradaPAL Installation Manual preview
StradaPAL
Brand: Parkeon Pages: 43
Mont Blanc ACTIVA+ Assembly Instructions preview
ACTIVA+
Brand: Mont Blanc Pages: 2
Vauxhall Crossland X 2017 Owner'S Manual preview
Crossland X 2017
Brand: Vauxhall Pages: 245
PEUGEOT BOXER 2018 Handbook preview
BOXER 2018
Brand: PEUGEOT Pages: 232
TracRac TracONE Installation Instructions Manual preview
TracONE
Brand: TracRac Pages: 8
Mercedes-Benz GLC 2020 Operator'S Manual preview
GLC 2020
Brand: Mercedes-Benz Pages: 66
RAM PROMASTER 2021 Owner'S Manual preview
PROMASTER 2021
Brand: RAM Pages: 288
Prorack K129 Fitting Instructions Manual preview
K129
Brand: Prorack Pages: 13
v.link VL2-CIC Manual preview
VL2-CIC
Brand: v.link Pages: 15
Edelbrock 1465 Installation Instructions preview
1465
Brand: Edelbrock Pages: 1

Brands by name

Popular brands

Load more brands