manualshive.com logo in svg

Dodge 2008 Avenger, Owner'S Manual

The Dodge 2008 Avenger Owner's Manual is your go-to guide for getting the most out of your vehicle. This comprehensive manual covers everything from maintenance and troubleshooting to important safety information. Download your free copy from manualshive.com and enjoy the peace of mind that comes with knowing your vehicle inside out.

Share
Download
background image

the parking brake is applied or a brake fault is detected.
If the light does not illuminate, have the light inspected
by an authorized dealer.

The light also will turn on when the parking brake is
applied with the ignition switch in the ON position.

NOTE:

This light shows only that the parking brake is

applied. It does not show the degree of brake application.

29. Electronic Vehicle Information Center (EVIC)
Display—Premium Cluster Only
This display shows the EVIC messages when the appro-
priate conditions exist. Refer to “Electronic Vehicle Infor-
mation Center (EVIC)” in this section for more informa-
tion.

ELECTRONIC VEHICLE INFORMATION CENTER
(EVIC) – IF EQUIPPED

EVIC Display Location

UNDERSTANDING YOUR INSTRUMENT PANEL

181

4

Summary of Contents for 2008 Avenger




















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2008 Avenger

Accel 2020 Installation Instructions preview
2020
Brand: Accel Pages: 2
Garmin BC 30 Owner'S Manual preview
BC 30
Brand: Garmin Pages: 2
RAM Commercial PROMASTER 2020 Quick Reference Manual preview
PROMASTER 2020
Brand: RAM Commercial Pages: 12
Warrior Winches C10000NH Assembly & Operating Instructions preview
C10000NH
Brand: Warrior Winches Pages: 17
Pacbrake C44059 Installation Manual preview
C44059
Brand: Pacbrake Pages: 14
Kia Picanto 2015 Quick Reference Manual preview
Picanto 2015
Brand: Kia Pages: 10
Dometic Heki 2 Installation And Operating Manual preview
Heki 2
Brand: Dometic Pages: 158
Mercedes-Benz 2016 SLK Operator'S Manual preview
2016 SLK
Brand: Mercedes-Benz Pages: 358
Thule 1430 Kit Instructions Manual preview
1430 Kit
Brand: Thule Pages: 8
EUFAB 16458 Operating Instructions Manual preview
16458
Brand: EUFAB Pages: 16
Air Lift 88365 Installation Manual preview
88365
Brand: Air Lift Pages: 28
Dolphin DAS400 Owner'S Manual preview
DAS400
Brand: Dolphin Pages: 16
APS IA06SJD4B Installation Instructions preview
IA06SJD4B
Brand: APS Pages: 3
Dodge 2010 Challenger SRT Owner'S Manual preview
2010 Challenger SRT
Brand: Dodge Pages: 444
Ford ALCON 1968 Owner'S Manual preview
ALCON 1968
Brand: Ford Pages: 52
Lexus LS 460 2011 Owner'S Manual preview
LS 460 2011
Brand: Lexus Pages: 830
Kleinn RS-GM6 Installation Manual preview
RS-GM6
Brand: Kleinn Pages: 8
PEUGEOT 5008 2017 Handbook preview
5008 2017
Brand: PEUGEOT Pages: 404

Brands by name

Popular brands

Load more brands