manualshive.com logo in svg

Dodge 2008 Avenger, Owner'S Manual

The Dodge 2008 Avenger Owner's Manual is your go-to guide for getting the most out of your vehicle. This comprehensive manual covers everything from maintenance and troubleshooting to important safety information. Download your free copy from manualshive.com and enjoy the peace of mind that comes with knowing your vehicle inside out.

Share
Download
background image

Do not run the engine in a closed garage or in confined
areas any longer than needed to move your vehicle in or
out of the area.

If it is necessary to sit in a parked vehicle with the engine
running, adjust your heating or cooling controls to force
outside air into the vehicle. Set the blower at high speed.

WARNING!

If you are required to drive with the deck lid open,
make sure that all windows are closed, and the
climate control blower switch is set at high speed.
DO NOT use the recirculation mode.

Safety Checks You Should Make Inside The
Vehicle

Seat Belts
Inspect the belt system periodically, checking for cuts,
frays and loose parts. Damaged parts must be replaced
immediately. Do not disassemble or modify the system.

Front seat belt assemblies must be replaced after a
collision. Rear seat belt assemblies must be replaced after
a collision if they have been damaged (bent retractor, torn
webbing, etc.). If there is any question regarding belt or
retractor condition, replace the belt.

Airbag Light
The light should come on and remain on for six to eight
seconds as a bulb check when the ignition switch is first
turned ON. If the LED is not lit during starting, have it
checked. If the light stays on or comes on while driving,
have the system checked by an authorized dealer.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

79

2

Summary of Contents for 2008 Avenger




















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2008 Avenger

Garmin BC 30 Owner'S Manual preview
BC 30
Brand: Garmin Pages: 2
UltraGauge EM Installation & Operation Manual preview
EM
Brand: UltraGauge Pages: 55
Xblitz G250 User Manual preview
G250
Brand: Xblitz Pages: 16
OEM Audio Reference Series Manual preview
Reference Series
Brand: OEM Audio Pages: 29
Fabbri BICI OK 2 Quick Start Manual preview
BICI OK 2
Brand: Fabbri Pages: 4
GMC SIERRA 2019 Getting To Know Your preview
SIERRA 2019
Brand: GMC Pages: 20
KRAFTWERK Automotive 31006 Instructions preview
Automotive 31006
Brand: KRAFTWERK Pages: 2
FALCON RIDGE HO-P500-FC04 Instructions For Installation And Care preview
HO-P500-FC04
Brand: FALCON RIDGE Pages: 8
Scosche 142HUD2 Manual preview
142HUD2
Brand: Scosche Pages: 8
KlipXtreme Ridesmart KMA-610 Manual preview
Ridesmart KMA-610
Brand: KlipXtreme Pages: 12
Arrista SG8-19 Installation Manual preview
SG8-19
Brand: Arrista Pages: 2
CSL 41802 User Manual preview
41802
Brand: CSL Pages: 8
Kuda 191090 Installation Instruction preview
191090
Brand: Kuda Pages: 3
OMNISTOR Omni-Bike Sport Ducato Installation preview
Omni-Bike Sport Ducato
Brand: OMNISTOR Pages: 5
Edelbrock Turbocharger 15012 Installation Instructions preview
Turbocharger 15012
Brand: Edelbrock Pages: 1
GMC Yukon XL Denali 2015 Owner'S Manual preview
Yukon XL Denali 2015
Brand: GMC Pages: 439
Westin 33-1920 Instructions preview
33-1920
Brand: Westin Pages: 3
Edelbrock 3824 Installation Instructions preview
3824
Brand: Edelbrock Pages: 2

Brands by name

Popular brands

Load more brands