Dodge 2008 Avenger Owner'S Manual Download Page 154 | Manualshive

Page: 154 / 467

background image

SUNSHADE OPERATION

The sunshade can be opened manually. However, the
sunshade will open automatically as the sunroof opens.

NOTE:

The sunshade cannot be closed if the sunroof is

open.

WIND BUFFETING

Wind buffeting can be described as the perception of
pressure on the ears or a helicopter type sound in the
ears. Your vehicle may exhibit wind buffeting with the
windows down, or the sunroof (if so equipped) in certain
open or partially open positions. This is a normal occur-
rence and can be minimized. If the buffeting occurs with
the rear windows open, then open the front and rear
windows together to minimize the buffeting. If the
buffeting occurs with the sunroof open, adjust the sun-
roof opening to minimize the buffeting.

SUNROOF MAINTENANCE

Use only a non-abrasive cleaner and a soft cloth to clean
the glass panel.

IGNITION OFF OPERATION

For vehicles not equipped with the Electronic Vehicle
Information Center (EVIC), the power sunroof switch
will remain active for 45 seconds after the ignition switch
is turned off. Opening either front door will cancel this
feature.

For vehicles equipped with the EVIC, the power sunroof
switch will remain active for up to 10 minutes after the
ignition switch is turned off. Opening either front door
will cancel this feature. The time is programmable. For
details, refer to “Key-Off Power Delay,” under “Personal
Settings (Customer Programmable Features)” under
“Electronic Vehicle Information Center (EVIC)” in Sec-
tion 4 of this manual.

152

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

«
...
152
153
154
155
156
...
»

Summary of Contents for 2008 Avenger




















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2008 Avenger

Brand: AA Products Pages: 6

Brand: Vauxhall Pages: 2

Brand: GOgroove Pages: 9

Brand: Mercedes-Benz Pages: 30

Brand: Dodge Pages: 24

Brand: E&G Classics Pages: 4

Brand: Tesla Pages: 274

Brand: Ratio Pages: 12

Brand: Horn Tools Pages: 8

Brand: Saab Pages: 37

Brand: TracRac Pages: 8

Brand: Mitsubishi Pages: 490

1995 Roadmaster

Brand: Buick Pages: 340

Brand: Westin Pages: 3

Brand: Kuda Pages: 4

Brand: Dacia Pages: 244

Brand: Aries Pages: 6

Brand: Thule Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands