Dodge 2008 Avenger Owner'S Manual Download Page 266 | Manualshive

Page: 266 / 467

background image

CAUTION!

To prevent damage to the starter, do not crank the
engine for more than 15 seconds at a time. Wait 10 to
15 seconds before trying again.

After Starting

The idle speed will automatically decrease as the engine
warms up.

Remote Starting System — If Equipped

Remote start conveniently starts the engine from outside
the vehicle by using the Remote Keyless Entry (RKE) key
fob while maintaining security. The system has a targeted
range of 328 ft (100 m). The vehicle must be locked, the
deck lid and hood closed and the transmission in PARK
in order to start the engine using the Remote Start button
on the key fob.

NOTE:

Remote start requires Automatic Transaxle

equipped vehicles.

How To Use Remote Start

To enter the Remote Start mode, depress the Remote Start
button twice on the key fob. The engine will start and the
vehicle will remain in the remote start mode for a 15
minute cycle.

264

STARTING AND OPERATING

«
...
264
265
266
267
268
...
»

Summary of Contents for 2008 Avenger




















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2008 Avenger

Brand: Camcar Pages: 6

Electronic Parking Disc II

Brand: Jacob Jensen Pages: 28

Brand: Fab Fours Pages: 19

Brand: E&G Classics Pages: 3

Brand: Skoda Pages: 281

Brand: PUTCO Pages: 2

Brand: rough country Pages: 4

Brand: NavInc Pages: 6

Denali 1094-0185-15

Brand: E&G Classics Pages: 3

Brand: Metra Electronics Pages: 2

Brand: Reliant Pages: 206

Brand: Magneti Marelli Pages: 3

Brand: Westfalia Pages: 2

Brand: Telwin Pages: 32

Brand: Acewell Pages: 7

Brand: LAMBORGHINI Pages: 43

Brand: Jeep Pages: 23

Brand: Jeep Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands