manualshive.com logo in svg

Dodge 2008 Avenger, Owner'S Manual

The Dodge 2008 Avenger Owner's Manual is your go-to guide for getting the most out of your vehicle. This comprehensive manual covers everything from maintenance and troubleshooting to important safety information. Download your free copy from manualshive.com and enjoy the peace of mind that comes with knowing your vehicle inside out.

Share
Download
background image

Seat Belt Extender
If a seat belt is too short, even when fully extended and
when the adjustable upper shoulder belt anchorage (if
equipped) is in its lowest position, your dealer can
provide you with a seat belt extender. This extender
should be used only if the existing belt is not long
enough. When it is not required, remove the extender,
and stow it.

WARNING!

Using a seat belt extender when not needed can
increase the risk of injury in a collision. Only use
when the lap belt is not long enough when it is worn
low and snug, and in the recommended seating
positions. Remove and store the extender when not
needed.

SUPPLEMENTAL RESTRAINT SYSTEM (SRS) -
AIRBAG

This vehicle has airbags for both the driver and front
passenger as a supplement to the seat belt restraint
systems. The driver’s front airbag is mounted in the
center of the steering wheel. The passenger’s front airbag
is mounted in the instrument panel, above the glove
compartment. The words SRS AIRBAG are embossed on
the airbag covers.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

51

2

Summary of Contents for 2008 Avenger




















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2008 Avenger

Saab 99 Important Operatlng, Safety And Maintenance Instructions preview
99
Brand: Saab Pages: 75
AAMP of America iSimple Operation Manual preview
iSimple
Brand: AAMP of America Pages: 6
Jetter JX3-BN-CAN Manual preview
JX3-BN-CAN
Brand: Jetter Pages: 4
K&K M5700N Manual preview
M5700N
Brand: K&K Pages: 8
K&K M4700 Manual preview
M4700
Brand: K&K Pages: 20
K&K M3500N Manual preview
M3500N
Brand: K&K Pages: 6
K&K M2500 Manual preview
M2500
Brand: K&K Pages: 3
K&K M1500 Manual preview
M1500
Brand: K&K Pages: 3
GOgroove SMARTmini AUX Operating Manual preview
SMARTmini AUX
Brand: GOgroove Pages: 9
Camcar 40061 Fe Mounting Instructions preview
40061 Fe
Brand: Camcar Pages: 2
Saleen 10-8002-C11998B Installation Manual preview
10-8002-C11998B
Brand: Saleen Pages: 12
Buick 2013 Buick Verano Manual preview
2013 Buick Verano
Brand: Buick Pages: 5
femkes Hopper on Top User Manual preview
Hopper on Top
Brand: femkes Pages: 7
Ecco 5545A Installation And Operating Instructions Manual preview
5545A
Brand: Ecco Pages: 12
Whispbar K951W Fitting Instructions For Basic Carrier preview
K951W
Brand: Whispbar Pages: 15
GMC TopKick 2007 Owner'S Manual preview
TopKick 2007
Brand: GMC Pages: 430
Air Lift 88365 Installation Manual preview
88365
Brand: Air Lift Pages: 28
Dolphin DAS400 Owner'S Manual preview
DAS400
Brand: Dolphin Pages: 16

Brands by name

Popular brands

Load more brands