manualshive.com logo in svg

Dodge 2008 Avenger, Owner'S Manual

The Dodge 2008 Avenger Owner's Manual is your go-to guide for getting the most out of your vehicle. This comprehensive manual covers everything from maintenance and troubleshooting to important safety information. Download your free copy from manualshive.com and enjoy the peace of mind that comes with knowing your vehicle inside out.

Share
Download
background image

WARNING!

The traction grade assigned to this tire is based on
straight-ahead braking traction tests, and does not
include acceleration, cornering, hydroplaning, or
peak traction characteristics.

Temperature Grades

The temperature grades are A (the highest), B, and C,
representing the tire’s resistance to the generation of heat
and its ability to dissipate heat, when tested under
controlled conditions on a specified indoor laboratory
test wheel. Sustained high temperature can cause the
material of the tire to degenerate and reduce tire life, and
excessive temperature can lead to sudden tire failure. The
grade C corresponds to a level of performance, which all
passenger car tires must meet under the Federal Motor

Vehicle Safety Standard No. 109. Grades B and A repre-
sent higher levels of performance on the laboratory test
wheel, than the minimum required by law.

WARNING!

The temperature grade for this tire is established for
a tire that is properly inflated and not overloaded.
Excessive speed, under-inflation, or excessive load-
ing, either separately or in combination, can cause
heat buildup and possible tire failure.

442

IF YOU NEED CONSUMER ASSISTANCE

Summary of Contents for 2008 Avenger




















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2008 Avenger

Hama Cup holder Operating Instruction preview
Cup holder
Brand: Hama Pages: 2
Abarth 124 SPIDER Service And Warranty Handbook preview
124 SPIDER
Brand: Abarth Pages: 36
Daihatsu S85 Wiring Diagrams preview
S85
Brand: Daihatsu Pages: 41
Daihatsu S85 Workshop Manual preview
S85
Brand: Daihatsu Pages: 268
Ecco EW4010 Installation And Operation Instructions Manual preview
EW4010
Brand: Ecco Pages: 9
Ecco EW4009 Installation And Operation Instructions Manual preview
EW4009
Brand: Ecco Pages: 9
TATA Motors Indigo Owner'S Manual & Service Book preview
Indigo
Brand: TATA Motors Pages: 164
Gardigo MARTEN-FREE CAR Instruction Manual preview
MARTEN-FREE CAR
Brand: Gardigo Pages: 36
HALE MM-03 Driver Manual preview
MM-03
Brand: HALE Pages: 44
U & Me Brothers LK-168A Manual preview
LK-168A
Brand: U & Me Brothers Pages: 6
P-Invent Troller User Manual preview
Troller
Brand: P-Invent Pages: 4
Caltrend BM110 Installation Instructions preview
BM110
Brand: Caltrend Pages: 2
Advanced ICE 1296-1 Manual preview
1296-1
Brand: Advanced ICE Pages: 4
Fortin Evo All THAR-FOR3 Installation Manual preview
Evo All THAR-FOR3
Brand: Fortin Pages: 7
Dodge Challenger 2013 Owner'S Manual preview
Challenger 2013
Brand: Dodge Pages: 543
Paccar DAF CHARGEMAX 90 User Manual preview
DAF CHARGEMAX 90
Brand: Paccar Pages: 40
Ranger design 1525-FTR Installation Manual preview
1525-FTR
Brand: Ranger design Pages: 24
Westin 31-0190 Installation Instructions preview
31-0190
Brand: Westin Pages: 2

Brands by name

Popular brands

Load more brands