manualshive.com logo in svg

Dodge 2008 Avenger, Owner'S Manual

The Dodge 2008 Avenger Owner's Manual is your go-to guide for getting the most out of your vehicle. This comprehensive manual covers everything from maintenance and troubleshooting to important safety information. Download your free copy from manualshive.com and enjoy the peace of mind that comes with knowing your vehicle inside out.

Share
Download
background image

Gross Axle Weight Rating (GAWR)
The GAWR is the maximum capacity of the front and rear
axles. Distribute the load over the front and rear axles
evenly. Make sure that you do not exceed either front or
rear GAWR.

WARNING!

It is important that you do not exceed the maximum
front or rear GAWR. A dangerous driving condition
can result if either rating is exceeded. You could lose
control of the vehicle and have an accident.

Trailer Tongue Weight (TW)
Tongue Weight is the downward force exerted on the
hitch ball by the trailer. In most cases it should not be less
than or more than 10% of the trailer load. You must
consider this as part of the load on your vehicle.

Frontal Area
Frontal Area is the maximum height and maximum
width of the front of a trailer and its cargo.

Weight-Carrying Hitch
A weight-carrying hitch supports the trailer tongue
weight, just as if it were luggage located at a hitch ball or
some other connecting point of the truck. These kinds of
hitches are the most popular on the market today and
they’re commonly used to tow small- and medium-sized
trailers.

STARTING AND OPERATING

335

5

Summary of Contents for 2008 Avenger




















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2008 Avenger

A-Tach Mounts 50131 Instructions preview
50131
Brand: A-Tach Mounts Pages: 2
Toyota 2012 Rav4 Owner'S Manual preview
2012 Rav4
Brand: Toyota Pages: 529
Waeco MagicWatch MWE800 Installation And Operating Manual preview
MagicWatch MWE800
Brand: Waeco Pages: 212
Toyota RX450h 2010 Emergency Response Manual preview
RX450h 2010
Brand: Toyota Pages: 35
Mercedes-Benz R-Class Owner'S Manual preview
R-Class
Brand: Mercedes-Benz Pages: 373
hc-cargo 171850 Mounting And Operation Instructions preview
171850
Brand: hc-cargo Pages: 60
Ecco 5545A Installation And Operating Instructions Manual preview
5545A
Brand: Ecco Pages: 12
Fiat Fiat Bravo LPG Owner'S Manual preview
Fiat Bravo LPG
Brand: Fiat Pages: 24
Valeo AS1A Owner'S Manual preview
AS1A
Brand: Valeo Pages: 28
Pacbrake HP10098 Installation Manual preview
HP10098
Brand: Pacbrake Pages: 6
Cadillac 1999 Escalade Owner'S Manual preview
1999 Escalade
Brand: Cadillac Pages: 352
Paser UNICOM JVC Installation Manual preview
UNICOM JVC
Brand: Paser Pages: 2
Xblitz XME PRO User Manual preview
XME PRO
Brand: Xblitz Pages: 56
N-Com Bluetooth Kit3 PLUS User Instructions And Safety preview
Bluetooth Kit3 PLUS
Brand: N-Com Pages: 36
Waeco MagicSpeed MS900 Installation Manual preview
MagicSpeed MS900
Brand: Waeco Pages: 120
Ford TRANSIT CUSTOM Quick Reference Manual preview
TRANSIT CUSTOM
Brand: Ford Pages: 15
Honda 08L04-SZA-100 Installation Instructions preview
08L04-SZA-100
Brand: Honda Pages: 3
SSV Works RG4-DM3 Manual preview
RG4-DM3
Brand: SSV Works Pages: 2

Brands by name

Popular brands

Load more brands