manualshive.com logo in svg

Dodge 2008 Avenger, Owner'S Manual

The Dodge 2008 Avenger Owner's Manual is your go-to guide for getting the most out of your vehicle. This comprehensive manual covers everything from maintenance and troubleshooting to important safety information. Download your free copy from manualshive.com and enjoy the peace of mind that comes with knowing your vehicle inside out.

Share
Download
background image

HAZARD WARNING FLASHER

The flasher switch is located on the instrument
panel, below the radio. Depress the switch and
both cluster indicators and all front and rear direc-

tional signals will flash. Depress the switch again to turn
Hazard Warning Flashers off.

Do not use this emergency warning system when the
vehicle is in motion. Use it when your vehicle is disabled
and it is creating a safety hazard for other motorists.

If it is necessary to leave the vehicle to go for service, the
flasher system will continue to operate with the ignition
key removed and the vehicle locked.

NOTE:

With extended use, the flasher may wear down

your battery.

IF YOUR ENGINE OVERHEATS

In any of the following situations, you can reduce the
potential for overheating by taking the appropriate ac-
tion.

•

On the highways — Slow down.

•

In city traffic — While stopped, put transaxle in
NEUTRAL, but do not increase engine idle speed.

If the pointer rises to the H (red) mark, the instrument
cluster will sound a chime. Pull over and stop the vehicle
with the engine at idle, when safe. Turn off the air
conditioning and wait until the pointer drops back into
the normal range. If the pointer remains on the H (red)
mark for more than a minute, turn the engine off imme-
diately and call for service.

348

WHAT TO DO IN EMERGENCIES

Summary of Contents for 2008 Avenger




















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2008 Avenger

AA Products X31 Instruction Manual preview
X31
Brand: AA Products Pages: 6
VanEssa mobilcamping V1 User Instruction preview
V1
Brand: VanEssa mobilcamping Pages: 8
Fabbri BICI OK 2 Quick Start Manual preview
BICI OK 2
Brand: Fabbri Pages: 4
B-Speech Pago INBTHF020 User Manual preview
Pago INBTHF020
Brand: B-Speech Pages: 24
IBASE Technology MPT-3000V User Manual preview
MPT-3000V
Brand: IBASE Technology Pages: 100
Modifry Products S2000 Windscreen Camera Mount Quick Start Manual preview
S2000 Windscreen Camera Mount
Brand: Modifry Products Pages: 2
hc-cargo 171850 Mounting And Operation Instructions preview
171850
Brand: hc-cargo Pages: 60
Thule Kit 1429 Fitting Instructions Manual preview
Kit 1429
Brand: Thule Pages: 8
Cadillac 2004 ESCALADE Customer Convenience/Personalization Manual preview
2004 ESCALADE
Brand: Cadillac Pages: 20
Scion 2012 iQ Quick Reference Manual preview
2012 iQ
Brand: Scion Pages: 24
Car-Systems Parktronic system Volkswagen Golf MK7 Assembly Manual preview
Parktronic system Volkswagen Golf MK7
Brand: Car-Systems Pages: 10
Black Horse Off Road TO20 Installation Instructions Manual preview
TO20
Brand: Black Horse Off Road Pages: 7
Thule 953000 Instructions Manual preview
953000
Brand: Thule Pages: 8
Metra Electronics 99-5026 Installation Instructions Manual preview
99-5026
Brand: Metra Electronics Pages: 20
Mazda 3 Facelift 2006 Training Manual preview
3 Facelift 2006
Brand: Mazda Pages: 94
Pet Gear TL9000 Instruction Manual preview
TL9000
Brand: Pet Gear Pages: 4
Suzuki IGNIS 2022 Series Manual preview
IGNIS 2022 Series
Brand: Suzuki Pages: 570
TOP VEHICLE TECH GR3FORD5 Installation Manual preview
GR3FORD5
Brand: TOP VEHICLE TECH Pages: 8

Brands by name

Popular brands

Load more brands