Dodge 2008 Avenger Owner'S Manual Download Page 302 | Manualshive

Page: 302 / 467

background image

2. Economy—
Improper inflation pressures can cause uneven wear
patterns to develop across the tire tread. These abnormal
wear patterns will reduce tread life resulting in a need for
earlier tire replacement. Under inflation, also increases
tire rolling resistance and results in higher fuel consump-
tion.

3. Ride Comfort and Vehicle Stability—
Proper tire inflation contributes to a comfortable ride.
Over inflation produces a jarring and uncomfortable ride.

Tire Inflation Pressures

The proper cold tire inflation pressure is listed either on
the face of the driver’s door or on the driver’s side “B”
pillar.

Some vehicles may have Supplemental Tire Pressure
Information for vehicle loads that are less than the

maximum loaded vehicle condition. These pressure con-
ditions will be found in the “Supplemental Tire Pressure
Information” section of this manual.

The pressure should be checked and adjusted as well as
inspecting for signs of tire wear or visible damage at least
once a month. Use a good quality pocket-type gauge to

Tire Placard Location

300

STARTING AND OPERATING

«
...
300
301
302
303
304
...
»

Summary of Contents for 2008 Avenger




















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2008 Avenger

Brand: GMC Pages: 140

Brand: ECS Electronics Pages: 16

adaptiv mini ADVM-BM1

Brand: Connects2 Pages: 4

Brand: BMW Pages: 55

Brand: Whispbar Pages: 15

Brand: Chevrolet Pages: 428

Brand: GMC Pages: 430

2013 GMC Savana

Brand: GMC Pages: 398

Brand: QA1 Pages: 3

Brand: Prorack Pages: 14

Brand: Mercedes-Benz Pages: 493

Brand: Audi Pages: 4

Brand: Thule Pages: 15

Black Bison Sports Series

Brand: Wald Pages: 7

Brand: Gator Pages: 5

Brand: XTC Pages: 2

Brand: Nav TV Pages: 8

Brand: Volkswagen Pages: 188

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands