Dodge 2008 Avenger Owner'S Manual Download Page 301 | Manualshive

Page: 301 / 467

background image

WARNING!

Overloading of your tires is dangerous. Overloading
can cause tire failure, affect vehicle handling, and
increase your stopping distance. Use tires of the
recommended load capacity for your vehicle. Never
overload them.

TIRES — GENERAL INFORMATION

Tire Pressure

Proper tire inflation pressure is essential to the safe and
satisfactory operation of your vehicle. Three primary
areas are affected by improper tire pressure:

1. Safety—

WARNING!

•

Improperly inflated tires are dangerous and can cause

accidents.

•

Under inflation increases tire flexing and can result in

tire failure.

•

Over inflation reduces a tire’s ability to cushion shock.

Objects on the road and chuckholes can cause damage
that result in tire failure.

•

Unequal tire pressures can cause steering problems.

You could lose control of your vehicle.

•

Over inflated or under inflated tires can affect vehicle

handling and can fail suddenly, resulting in loss of
vehicle control.

•

Unequal tire pressures from one side of the vehicle to

the other can cause the vehicle to drift to the right or left.

•

Always drive with each tire inflated to the recom-

mended cold tire inflation pressure.

STARTING AND OPERATING

299

5

«
...
299
300
301
302
303
...
»

Summary of Contents for 2008 Avenger




















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2008 Avenger

Brand: Triumph Pages: 86

Brand: Bestop Pages: 11

Brand: Whispbar Pages: 14

2014 Insignia VXR SuperSport

Brand: Vauxhall Pages: 56

Brand: Kia Pages: 10

Brand: SnapPad Pages: 5

Brand: Compass Pages: 16

Wireless Handsfree Car Kit

Brand: Wagan Pages: 20

DELTA DL FIX 209FP

Brand: Menabo Pages: 8

Brand: Whispbar Pages: 17

Brand: POOL-LINE Pages: 2

Brand: Lexus Pages: 830

Brand: EUFAB Pages: 4

Brand: TIS Pages: 6

Brand: Yakima Pages: 12

Brand: APS Pages: 4

Sportsman 40-0125

Brand: Westin Pages: 2

Brand: Dacia Pages: 244

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands