Dodge 2008 Avenger Owner'S Manual Download Page 128 | Manualshive

Page: 128 / 467

background image

FOLDING REAR SEAT

To provide additional storage area, the rear seatback can
be folded forward. Pull on the loops shown in the picture
to fold down either or both seatbacks.

When returning the rear seat back to the upright position,
be sure the seat back is latched.

WARNING!

The rear cargo area of the vehicle (with the rear
seatbacks in the locked-up or folded down position)
should not be used as a play area by children. They
could be seriously injured in an accident. Children
should be seated and using the proper restraint
system.

Folding Rear Seats

126

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

«
...
126
127
128
129
130
...
»

Summary of Contents for 2008 Avenger




















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2008 Avenger

Brand: Toyota Pages: 52

Brand: Xpresskit Pages: 18

Brand: Thule Pages: 3

Brand: WABCO Pages: 34

Brand: POOL-LINE Pages: 2

MultiCharger 1204

Brand: DEFA Pages: 28

Brand: Steelmate Pages: 14

Brand: Club Car Pages: 286

Brand: Gentex Pages: 2

Brand: GROM Audio Pages: 20

Brand: Menabo Pages: 8

Brand: SSV Works Pages: 2

Brand: Scion Pages: 58

Brand: LaserLine Pages: 4

Brand: Mazda Pages: 7

Brand: N2MB Racing Pages: 13

Brand: Prorack Pages: 17

84 64 0 025 810

Brand: BMW Pages: 25

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands