Dodge 2008 Avenger Owner'S Manual Download Page 317 | Manualshive

Page: 317 / 467

background image

PREMIUM SYSTEM — IF EQUIPPED

The Tire Pressure Monitor System (TPMS) uses wireless
technology with wheel rim mounted electronic sensors to
monitor tire pressure levels. Sensors, mounted to each
wheel as part of the valve stem, transmit tire pressure
readings to the Receiver Module.

NOTE:

It is particularly important for you to check the

tire pressure in all of the tires on your vehicle monthly
and to maintain the proper pressure.

The TPMS consists of the following components:

•

Receiver Module

•

Four Tire Pressure Monitoring Sensors

•

Three Trigger Modules (mounted in three of the four
wheel-wells)

•

Various Tire Pressure Monitoring System Messages,
which display in the Electronic Vehicle Information
Center (EVIC)

•

Tire Pressure Monitoring Telltale Light

STARTING AND OPERATING

315

5

«
...
315
316
317
318
319
...
»

Summary of Contents for 2008 Avenger




















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2008 Avenger

Titanium Series

Brand: Fass Pages: 13

Brand: Parrot Pages: 19

Brand: Parrot Pages: 88

Brand: Parrot Pages: 2

Brand: Parrot Pages: 2

CK 3000 Evolution

Brand: Parrot Pages: 8

CK 3000 Evolution

Brand: Parrot Pages: 106

MagicWatch MWE800

Brand: Waeco Pages: 212

Brand: Alpine Pages: 69

Brand: Allen Sports Pages: 2

Brand: CITROEN Pages: 52

Brand: kincrome Pages: 6

Brand: Mercedes-Benz Pages: 373

Brand: Honda Pages: 32

Brand: Radical Sportscars Pages: 44

Brand: GARO Pages: 15

Brand: TAUBENREUTHER Pages: 18

Ridesmart KMA-610

Brand: KlipXtreme Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands