manualshive.com logo in svg

Dodge 2008 Avenger, Owner'S Manual

The Dodge 2008 Avenger Owner's Manual is your go-to guide for getting the most out of your vehicle. This comprehensive manual covers everything from maintenance and troubleshooting to important safety information. Download your free copy from manualshive.com and enjoy the peace of mind that comes with knowing your vehicle inside out.

Share
Download
background image

NOTE:

•

The temperature setting can be adjusted at anytime
without affecting automatic operation.

•

Pressing the Air Conditioning Control button while in
AUTO mode will cause the LED in the control button
to flash three times and then turn off. This indicates
that the system is in AUTO mode and requesting the
air conditioning is not necessary.

•

If your air conditioning performance seems lower than
expected, check the front of the A/C condenser (lo-
cated in front of the radiator) for an accumulation of
dirt or insects. Clean with a gentle water spray from
behind the radiator and through the condenser. Fabric
front fascia protectors may reduce airflow to the
condenser, reducing air conditioning performance.

Manual Operation
This system offers a full complement of manual override
features, which consist of Blower Preferred Automatic,
Mode Preferred Automatic, or Blower and Mode Pre-
ferred Automatic. This means the operator can override
the blower, the mode, or both. There is a manual blower
range for times when the AUTO setting is not desired.
The blower can be set to any fixed blower speed by
rotating the Blower Control knob (on the left).

NOTE:

Please read the Automatic Temperature Control

Operation Chart that follows for details.

248

UNDERSTANDING YOUR INSTRUMENT PANEL

Summary of Contents for 2008 Avenger




















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2008 Avenger

ZAPTEC Go Quick Manual preview
Go
Brand: ZAPTEC Pages: 64
ZAPTEC Go Installation Manual preview
Go
Brand: ZAPTEC Pages: 24
U.S. General 97845 Set Up And Operating Instructions preview
97845
Brand: U.S. General Pages: 5
PAC RadioPRO 5 RP5-GM41 Quick Start Manual preview
RadioPRO 5 RP5-GM41
Brand: PAC Pages: 3
Audiovox Prestige APS-45B Installation Manual preview
Prestige APS-45B
Brand: Audiovox Pages: 8
Volvo 1985 740 GL Owner'S Manual preview
1985 740 GL
Brand: Volvo Pages: 138
Motoalliance VIPER MA11922 Install Instructions Manual preview
VIPER MA11922
Brand: Motoalliance Pages: 8
CTEK D250S Dual Manual preview
D250S Dual
Brand: CTEK Pages: 84
Xhorse VVDI User Manual preview
VVDI
Brand: Xhorse Pages: 48
Ranger design 1525-FTR Installation Manual preview
1525-FTR
Brand: Ranger design Pages: 24
Veldo Teknoloji DUCATO Manual preview
DUCATO
Brand: Veldo Teknoloji Pages: 32
Lantronix FOX3 Series Hardware Manual preview
FOX3 Series
Brand: Lantronix Pages: 51
POOL-LINE 110085 Assembly Instructions preview
110085
Brand: POOL-LINE Pages: 2
Brodit ProClip 854676 Quick Start Manual preview
ProClip 854676
Brand: Brodit Pages: 2
Gentex ADVGEN20A Manual preview
ADVGEN20A
Brand: Gentex Pages: 2
TOP VEHICLE TECH GR3FORD5 Installation Manual preview
GR3FORD5
Brand: TOP VEHICLE TECH Pages: 8
Mazda 0000-8E-N31 Installation Instructions Manual preview
0000-8E-N31
Brand: Mazda Pages: 7
Connects2 CTQIAU03 Installation & User Manual preview
CTQIAU03
Brand: Connects2 Pages: 2

Brands by name

Popular brands

Load more brands