manualshive.com logo in svg

Dodge 2008 Avenger, Owner'S Manual

The Dodge 2008 Avenger Owner's Manual is your go-to guide for getting the most out of your vehicle. This comprehensive manual covers everything from maintenance and troubleshooting to important safety information. Download your free copy from manualshive.com and enjoy the peace of mind that comes with knowing your vehicle inside out.

Share
Download
background image

CAUTION!

Because of the reduced ground clearance, do not take
your vehicle through an automatic car wash with the
compact spare installed. Damage to the vehicle may
result.

Limited Use Spare — If Equipped

The limited use spare tire is for temporary emergency use
on your vehicle. This tire is identified by a limited use
spare tire warning label located on the limited use spare
tire and wheel assembly. This tire may look like the
original equipped tire on the front or rear axle of your
vehicle, but it is not. Installation of this limited use spare
tire affects vehicle handling. Since it is not the same tire,
replace (or repair) the original tire and reinstall on the
vehicle at the first opportunity.

WARNING!

The limited use spare tires are for emergency use
only. Installation of this limited use spare tire affects
vehicle handling. With this tire, do not drive more
than 50 mph (80 km/h). Keep inflated to the cold tire
inflation pressure listed on either your tire placard or
limited use spare tire and wheel assembly. Replace
(or repair) the original tire at the first opportunity
and reinstall it on your vehicle. Failure to do so could
result in loss of vehicle control.

304

STARTING AND OPERATING

Summary of Contents for 2008 Avenger




















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2008 Avenger

Lancia Delta Owner'S Handbook Manual preview
Delta
Brand: Lancia Pages: 276
T-Tech TT100 User Manual preview
TT100
Brand: T-Tech Pages: 38
Jeep Commander Overview Manual preview
Commander
Brand: Jeep Pages: 25
Jeep Commander Warranty Information Booklet preview
Commander
Brand: Jeep Pages: 51
Farenheit CCD-5XS Owner'S Manual preview
CCD-5XS
Brand: Farenheit Pages: 8
Subaru 2016 Outback Owner'S Manual preview
2016 Outback
Brand: Subaru Pages: 99
RAM 2011 DAKOTA User Manual preview
2011 DAKOTA
Brand: RAM Pages: 76
Advantech TREK-550 Manual preview
TREK-550
Brand: Advantech Pages: 59
BMW E46/2 Coupe Manual preview
E46/2 Coupe
Brand: BMW Pages: 55
Whispbar K496W Fitting Instructions Manual preview
K496W
Brand: Whispbar Pages: 15
WABCO OnSide MM16167 Maintenance Manual preview
OnSide MM16167
Brand: WABCO Pages: 52
Fortin Evo All THAR-FOR3 Installation Manual preview
Evo All THAR-FOR3
Brand: Fortin Pages: 7
Lit Lightz RGBW Rock Lights Setup Manual preview
RGBW Rock Lights
Brand: Lit Lightz Pages: 3
Mitsubishi MIrage 2019 Owner'S Handbook Manual preview
MIrage 2019
Brand: Mitsubishi Pages: 19
Honda 2006 Accord Owner'S Manual preview
2006 Accord
Brand: Honda Pages: 569
Vauxhall Crossland X 2017 Owner'S Manual preview
Crossland X 2017
Brand: Vauxhall Pages: 245
AutoLoc SB3PR Series User Manual And Installation Manual preview
SB3PR Series
Brand: AutoLoc Pages: 6
Lincoln NAUTILUS 2022 Owner'S Manual preview
NAUTILUS 2022
Brand: Lincoln Pages: 586

Brands by name

Popular brands

Load more brands