Dodge 2008 Avenger Owner'S Manual Download Page 148 | Manualshive

Page: 148 / 467

background image

If the indicator light stays on constantly, programming is
complete and the garage door (or device) should activate
when the HomeLink

t

button is pressed.

If the indicator light blinks rapidly for two seconds, and
then turns to a constant light, proceed to Step 5 “Pro-
gramming A Rolling Code System.”

5. Programming A Rolling Code System
At the garage door opener motor (in the garage), locate
the “Learn” or “Training” button.

This can usually be found where the hanging antenna
wire is attached to the garage door opener motor (it is
NOT the button normally used to open and close the
door).

6. Firmly press and release the “Learn” or “Training”
button. The name and color of the button may vary by
manufacturer.

GARAGE DOOR OPENER TRAIN BUTTON

1 — Door Opener

2 — Training Button

146

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

«
...
146
147
148
149
150
...
»

Summary of Contents for 2008 Avenger




















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2008 Avenger

Brand: ZAPTEC Pages: 64

Brand: ZAPTEC Pages: 24

Brand: Happy Orange Pages: 2

Brand: DANA Pages: 42

Brand: dallara Pages: 37

Brand: Yakima Pages: 8

Brand: Thule Pages: 8

Brand: Hyundai Pages: 19

Brand: EUFAB Pages: 16

Brand: Bestop Pages: 4

Easy Air Auto Screen

Brand: Wagan Pages: 8

Brand: Prorack Pages: 15

Bluetooth Kit3 PLUS

Brand: N-Com Pages: 36

Brand: Voxx Electronics Pages: 15

Brand: Rydeen Pages: 14

Brand: Renault Pages: 3699

Brand: QA1 Pages: 3

Brand: Menabo Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands