Dodge 2008 Avenger Owner'S Manual Download Page 466 | Manualshive

Page: 466 / 467

background image

INSTALLATION OF RADIO TRANSMITTING
EQUIPMENT

Special design considerations are incorporated into this
vehicle’s electronic system to provide immunity to radio
frequency signals. Mobile two-way radios and telephone
equipment must be installed properly by trained person-
nel. The following must be observed during installation.

The positive power connection should be made directly
to the battery and fused as close to the battery as possible.
The negative power connection should be made to body
sheet metal adjacent to the negative battery connection.
This connection should not be fused.

Antennas for two-way radios should be mounted on the
roof or the rear area of the vehicle. Care should be used
in mounting antennas with magnet bases. Magnets may
affect the accuracy or operation of the compass on
vehicles so equipped.

The antenna cable should be as short as practical and
routed away from the vehicle wiring when possible. Use
only fully shielded coaxial cable.

Carefully match the antenna and cable to the radio to
ensure a low Standing Wave Ratio (SWR).

Mobile radio equipment with output power greater than
normal may require special precautions.

All installations should be checked for possible interfer-
ence between the communications equipment and the
vehicle’s electronic systems.

«
...
464
465
466
467
»

Summary of Contents for 2008 Avenger




















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2008 Avenger

Brand: Daihatsu Pages: 1718

2011 Corolla LE

Brand: Toyota Pages: 19

Brand: Dynojet Pages: 68

Brand: Kuda-Phonebase Pages: 3

Brand: Kia Pages: 54

Brand: iArmor Pages: 4

Brand: Nav TV Pages: 5

Ram Commercial2016

Brand: Dodge Pages: 675

Brand: Yakima Pages: 11

Brand: iDataLink Pages: 6

Brand: A-Tach Mounts Pages: 2

Brand: Saab Pages: 9

1993 Civic Coupe

Brand: Honda Pages: 201

Brand: Yakima Pages: 12

Brand: NavLinkz Pages: 26

Brand: Safe Fleet Pages: 2

Brand: AEV Pages: 16

Brand: Ford Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands