Dodge 2008 Avenger Owner'S Manual Download Page 392 | Manualshive

Page: 392 / 467

background image

CAUTION!

•

Mixing of coolants other than specified HOAT
engine coolants, may result in engine damage and
may decrease corrosion protection. If a non-HOAT
coolant is introduced into the cooling system in an
emergency, it should be replaced with the speci-
fied coolant as soon as possible.

•

Do not use plain water alone or alcohol-base
engine coolant (antifreeze) products. Do not use
additional rust inhibitors or antirust products, as
they may not be compatible with the radiator
engine coolant and may plug the radiator.

•

This vehicle has not been designed for use with
Propylene Glycol based coolants. Use of Propy-
lene Glycol based coolants is not recommended.

Adding Coolant
Your vehicle has been built with an improved engine
coolant that allows extended maintenance intervals. This
coolant can be used up to 5 Years or 100,000 mi (160 000
km) before replacement. To prevent reducing this ex-
tended maintenance period, it is important that you use
the same coolant throughout the life of your vehicle.
Please review these recommendations for using Hybrid
Organic Additive Technology (HOAT) coolant.

When adding coolant:

•

The

manufacturer

recommends

using

Mopar

t

Antifreeze/Coolant 5 Year/100,000 Mile Formula
HOAT (Hybrid Organic Additive Technology).

•

Mix a minimum solution of 50% HOAT engine coolant
and distilled water. Use higher concentrations (not to
exceed 70%) if temperatures below

2

34 F (

2

37 C) are

anticipated.

390

MAINTAINING YOUR VEHICLE

«
...
390
391
392
393
394
...
»

Summary of Contents for 2008 Avenger




















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2008 Avenger

Brand: Federal Signal Corporation Pages: 8

Brand: Federal Signal Corporation Pages: 8

Brand: Kolpin Pages: 25

Brand: Audi Pages: 9

Brand: Belkin Pages: 4

Brand: TATA Motors Pages: 92

Brand: Whispbar Pages: 15

Brand: SCC Pages: 4

Brand: Carcomm Pages: 2

Brand: Gator Pages: 6

Brand: Honda Pages: 253

Brand: Toyota Pages: 11

Brand: Jaeger Pages: 13

GM DELTA 88 1974

Brand: Oldsmobile Pages: 88

VISTA-CRUISER 1970

Brand: Oldsmobile Pages: 67

Proguard 100021

Brand: walser Pages: 12

Brand: Thule Pages: 1

Brand: CITROËN Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands