manualshive.com logo in svg

Dodge 2008 Avenger, Owner'S Manual

The Dodge 2008 Avenger Owner's Manual is your go-to guide for getting the most out of your vehicle. This comprehensive manual covers everything from maintenance and troubleshooting to important safety information. Download your free copy from manualshive.com and enjoy the peace of mind that comes with knowing your vehicle inside out.

Share
Download
background image

FRONT AND REAR WHEEL BEARINGS

Front and rear wheel bearings are permanently sealed.
No regular maintenance is required for these compo-
nents.

APPEARANCE CARE AND PROTECTION FROM
CORROSION

Protection of Body and Paint from Corrosion
Vehicle body care requirements vary according to geo-
graphic locations and usage. Chemicals that make roads
passable in snow and ice and those that are sprayed on
trees and road surfaces during other seasons are highly
corrosive to the metal in your vehicle. Outside parking,
which exposes your vehicle to airborne contaminants,
road surfaces on which the vehicle is operated, extreme
hot or cold weather and other extreme conditions will
have an adverse effect on paint, metal trim, and under-
body protection.

The following maintenance recommendations will enable
you to obtain maximum benefit from the corrosion
resistance built into your vehicle.

What Causes Corrosion?
Corrosion is the result of deterioration or removal of
paint and protective coatings from your vehicle.

The most common causes are:

•

Road salt, dirt, and moisture accumulation.

•

Stone and gravel impact.

•

Insects, tree sap, and tar.

•

Salt in the air near seacoast localities.

•

Atmospheric fallout/industrial pollutants.

400

MAINTAINING YOUR VEHICLE

Summary of Contents for 2008 Avenger




















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2008 Avenger

Daihatsu F300 Service Manual preview
F300
Brand: Daihatsu Pages: 1718
Baja Designs S8 Instructions Manual preview
S8
Brand: Baja Designs Pages: 6
Yakima K618 Instructions Manual preview
K618
Brand: Yakima Pages: 11
UMBRA RIMORCHI 39030 Installation Instructions Manual preview
39030
Brand: UMBRA RIMORCHI Pages: 18
Uebler F42 Mounting And Operating Instructions preview
F42
Brand: Uebler Pages: 18
CITROËN C4 CACTUS Handbook preview
C4 CACTUS
Brand: CITROËN Pages: 301
Dacia 2014 Sandero Driver'S Handbook Manual preview
2014 Sandero
Brand: Dacia Pages: 238
Safe Fleet PRIME DESIGN VBI-FT21B Manual preview
PRIME DESIGN VBI-FT21B
Brand: Safe Fleet Pages: 12
Honda Plusone Console 4521011B User Information preview
Plusone Console 4521011B
Brand: Honda Pages: 4
mtf TRANSPORT SYSTEM BackPower Manual preview
BackPower
Brand: mtf TRANSPORT SYSTEM Pages: 9
Skoda OCTAVIA - TECHNICAL CHANGES 11-2009 Owner'S Manual Supplement preview
OCTAVIA - TECHNICAL CHANGES 11-2009
Brand: Skoda Pages: 16
Reese Explore 63153 Instruction Manual preview
63153
Brand: Reese Explore Pages: 9
CrimeStopper CA-504.BRKT Install Manual preview
CA-504.BRKT
Brand: CrimeStopper Pages: 1
Volvo 1989 780 Owner'S Manual preview
1989 780
Brand: Volvo Pages: 123
TOGU Airgo Active cushion / Comfort Manual And Maintenance Instructions preview
Airgo Active cushion / Comfort
Brand: TOGU Pages: 2
Vmac A700308 Installation Manual preview
A700308
Brand: Vmac Pages: 16
Yakima K1198 Instructions Manual preview
K1198
Brand: Yakima Pages: 10
Weather Guard 234-3-01 Installation Manual preview
234-3-01
Brand: Weather Guard Pages: 8

Brands by name

Popular brands

Load more brands