Dodge 2008 Avenger Owner'S Manual Download Page 159 | Manualshive

Page: 159 / 467

background image

1. The left latch opens to the top storage area.

2. The lower bin can be accessed directly, without first
exposing the upper bin, by operating the right latch with
the armrest down.

3. The first storage bin can be used to hold smaller items.

4. The lower storage bin includes a molded-in coin
holder, room for CDs, DVDs, and a power outlet that
allows a cell phone to recharge while concealed.

NOTE:

A notch in the side of the console base under the

armrest will also allow use of cell phone while still
plugged into the power outlet and with the armrest
latched down.

NOTE:

The power outlet located inside the console can

also energize the cigar lighter in the available Smoker’s
Package.

VIDEO CONSOLE — IF EQUIPPED

The optional VES™(Video Entertainment System) in-
cludes the following components:

•

The screen for a rear seat DVD player is stored under
the armrest.

•

Remote Control

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

157

3

«
...
157
158
159
160
161
...
»

Summary of Contents for 2008 Avenger




















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2008 Avenger

Multiple G9F18 AU000

Brand: Genesis Pages: 3

Brand: Yakima Pages: 19

UCI-11C NTV-KIT331

Brand: Nav TV Pages: 4

Brand: Edelbrock Pages: 2

Brand: Fiat Pages: 172

Brand: Honda Pages: 6

Brand: Saab Pages: 3

Brand: Thule Pages: 12

Brand: Skoda Pages: 281

Hatch-bag Luggage System

Brand: Tabernus Peram Pages: 10

Brand: WABCO Pages: 34

Brand: RAM Pages: 330

Brand: Brodit Pages: 2

Brand: Saturn Pages: 432

Brand: Renault Pages: 11

Brand: Edelbrock Pages: 2

Brand: Whispbar Pages: 18

Brand: Prorack Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands