Dodge 2008 Avenger Owner'S Manual Download Page 156 | Manualshive

Page: 156 / 467

background image

The center console power outlet is powered directly from
the battery (power available at all times). Items plugged
into this outlet may discharge the battery and/or prevent
engine starting.

Electrical Outlet Use With Engine Off

CAUTION!

•

Many accessories that can be plugged in draw
power from the vehicle’s battery, even when not in
use (i.e. cellular phones, etc.). Eventually, if
plugged in long enough, the vehicle’s battery will
discharge sufficiently to degrade battery life
and/or prevent engine starting.

•

Accessories that draw higher power (i.e. coolers,
vacuum cleaners, lights, etc.) will degrade the
battery even more quickly. Only use these inter-
mittently and with greater caution.

•

After the use of high power draw accessories, or
long periods of the vehicle not being started (with
accessories still plugged in), the vehicle must be
driven a sufficient length of time to allow the
generator to recharge the vehicle’s battery.

Console Interior

154

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

«
...
154
155
156
157
158
...
»

Summary of Contents for 2008 Avenger




















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2008 Avenger

Brand: Jeep Pages: 212

Brand: LAS Pages: 44

Brand: LAS Pages: 24

Brand: Dynojet Pages: 68

Brand: Kuda-Phonebase Pages: 3

Brand: Subaru Pages: 34

Brand: TATA Motors Pages: 159

Brand: ICON Pages: 4

Brand: Saturn Pages: 440

2011 SRX CROSSOVER

Brand: Cadillac Pages: 416

Brand: TIE DOWN Pages: 2

2917 Nstallation

Brand: Edelbrock Pages: 1

Brand: Curtis Pages: 6

Brand: true-i Pages: 11

Brand: MayPole Pages: 3

HFC7151M1V-U221B

Brand: JAC Pages: 106

Automobille 2004 Century

Brand: Buick Pages: 12

Brand: chinavasion Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands