Dodge 2008 Avenger Owner'S Manual Download Page 103 | Manualshive

Page: 103 / 467

background image

•

After the

9

Ready

9

prompt and the following beep, say

the name of the language you wish to switch to
English, Espanol, or Francais.

•

Continue to follow the system prompts to complete
language selection.

After selecting one of the languages, all prompts and
voice commands will be in that language.

NOTE:

After every UConnect

t

language change opera-

tion, only the language-specific 32-name phonebook is
usable. The paired phone name is not language-specific
and usable across all languages.

Emergency Assistance
If you are in an emergency and the mobile phone is
reachable:

•

Pick up the phone and manually dial the emergency
number for your area.

If the phone is not reachable and the UConnect

t

system

is operational, you may reach the emergency number as
follows:

•

Press the PHONE button to begin.

•

After the

9

Ready

9

prompt and the following beep, say

9

Emergency

9

and the UConnect

t

system will instruct

the paired cellular phone to call the emergency num-
ber. This feature is supported in the U.S., Canada, and
Mexico.

NOTE:

The emergency number dialed is based on the

country where the vehicle is purchased (911 for the U.S.
and Canada and 060 for Mexico). The number dialed may
not be applicable with the available cellular service and
area.

The UConnect

t

system does slightly lower your chances

of successfully making a phone call as to that for the cell
phone directly.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

101

3

«
...
101
102
103
104
105
...
»

Summary of Contents for 2008 Avenger




















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2008 Avenger

Brand: Baja Designs Pages: 6

Brand: Zavoli Pages: 26

Brand: 3SIXT Pages: 12

Brand: Alpine Pages: 8

2005 Sierra Denali

Brand: GMC Pages: 428

Brand: Mercedes-Benz Pages: 346

Brand: Thule Pages: 4

Brand: EUFAB Pages: 52

Brand: Van Guard Pages: 3

Brand: RAM Pages: 13

Brand: Softride Pages: 4

Brand: DFI Pages: 6

Brand: Subaru Pages: 540

1995 Cutlass Supreme

Brand: Oldsmobile Pages: 340

iTrip Bluetooth

Brand: Griffin Technology Pages: 6

Pajero Pinin 1999

Brand: Mitsubishi Pages: 919

Turbocharger 15012

Brand: Edelbrock Pages: 1

Yukon XL Denali 2015

Brand: GMC Pages: 439

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands