manualshive.com logo in svg

Dodge 2008 Avenger, Owner'S Manual

The Dodge 2008 Avenger Owner's Manual is your go-to guide for getting the most out of your vehicle. This comprehensive manual covers everything from maintenance and troubleshooting to important safety information. Download your free copy from manualshive.com and enjoy the peace of mind that comes with knowing your vehicle inside out.

Share
Download
background image

INTRODUCTION

This Owner’s Manual has been prepared with the assis-
tance of service and engineering specialists to acquaint
you with the operation and maintenance of your vehicle.
It is supplemented by a Warranty Information Booklet
and various customer-oriented documents. You are
urged to read these publications carefully. Following the
instructions and recommendations in this manual will
help assure safe and enjoyable operation of your vehicle.

NOTE: After you read the manual, it should be stored
in the vehicle for convenient reference and remain with
the vehicle when sold, so that the new owner will be
aware of all safety warnings.

When it comes to service, remember that your authorized
dealer knows your vehicle best, has the factory-trained
technicians and genuine Mopar

t

parts, and is interested

in your satisfaction.

HOW TO USE THIS MANUAL

Consult the table of contents to determine which section
contains the information you desire.

The detailed index, at the rear of this manual, contains a
complete listing of all subjects.

Consult the following table for a description of the
symbols that may be used on your vehicle or throughout
this owner manual:

4

INTRODUCTION

Summary of Contents for 2008 Avenger




















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2008 Avenger

Quadratec QuadraTop Adventure Top S Installation Manual preview
QuadraTop Adventure Top S
Brand: Quadratec Pages: 20
Ford 2008 Mustang Quick Reference Manual preview
2008 Mustang
Brand: Ford Pages: 2
Kuda-Phonebase 055040 Installation Instruction preview
055040
Brand: Kuda-Phonebase Pages: 3
GMC SIERRA 2002 Manual preview
SIERRA 2002
Brand: GMC Pages: 499
Kia Amanti Owner'S Manual preview
Amanti
Brand: Kia Pages: 290
Pontiac 2004 Vibe Navigation System Owner'S Manual preview
2004 Vibe Navigation System
Brand: Pontiac Pages: 44
K&M MILSCO KIT# C746700 Installation Manual preview
MILSCO KIT# C746700
Brand: K&M Pages: 2
Car-Interface CI-RL4-NAC12 Manual preview
CI-RL4-NAC12
Brand: Car-Interface Pages: 25
Thule 2 Bike Carrier 977 Instructions Manual preview
2 Bike Carrier 977
Brand: Thule Pages: 6
Hella AREIA 7040 Installation Instructions Manual preview
AREIA 7040
Brand: Hella Pages: 21
Mynew Portable Car Umbrella User Manual preview
Portable Car Umbrella
Brand: Mynew Pages: 5
GROM Audio VLINE Installation Manual preview
VLINE
Brand: GROM Audio Pages: 20
Reliant Rebel 700 1967 Workshop Manual preview
Rebel 700 1967
Brand: Reliant Pages: 116
Brodit Getac T800 Quick Start Manual preview
Getac T800
Brand: Brodit Pages: 2
Saturn 2009 OUTLOOK Owner'S Manual preview
2009 OUTLOOK
Brand: Saturn Pages: 432
JBA 1528S Installation Instructions And Warranty Information preview
1528S
Brand: JBA Pages: 5
iSimple IS7705 Installation & Operation Manual preview
IS7705
Brand: iSimple Pages: 8
PEUGEOT 5008 2017 Handbook preview
5008 2017
Brand: PEUGEOT Pages: 404

Brands by name

Popular brands

Load more brands