Dodge 2008 Avenger Owner'S Manual Download Page 185

Page: 185 / 467

Press and release the RESET button to accept a
selection. The RESET button also resets various
Trip Functions.

EVIC DISPLAYS

When the appropriate conditions exist, the Electronic
Vehicle Information Center (EVIC) displays the following
messages.

•

Turn Signal On (with a continuous warning chime)

•

Left Front Turn Signal Light Out (with a single chime)

•

Left Rear Turn Signal Light Out (with a single chime)

•

Right Front Turn Signal Light Out (with a single
chime)

•

Right Rear Turn Signal Light Out (with a single chime)

•

RKE (Remote Keyless Entry) Battery Low (with a
single chime)

•

Personal Settings Not Available – Vehicle Not In
PARK.

•

Left/Right Door Ajar (one or more, with a single
chime if speed is above 1 mph / 1 km h)

•

Door(s) Ajar (with a single chime if vehicle is in
motion)

•

Trunk Ajar (with a single chime)

•

Headlights On

•

Key In Ignition

•

Speed Too High (with a single chime)

•

Oil Change Required (with a single chime)

RESET

Button

UNDERSTANDING YOUR INSTRUMENT PANEL

183

Summary of Contents for 2008 Avenger




















































































































































































































































































































































































































































































Search results

Summary of Contents for 2008 Avenger

Reviews:

Related manuals for 2008 Avenger

Brands by name

Popular brands

Dodge 2008 Avenger, Owner'S Manual

Search results

Summary of Contents for 2008 Avenger

Reviews:

Related manuals for 2008 Avenger

Brands by name

Popular brands