Dodge 2008 Avenger Owner'S Manual Download Page 245 | Manualshive

Page: 245 / 467

background image

Blower Control

Use this control to regulate the
amount of air forced through the ven-
tilation system in any mode. The
blower speed increases as you move
the control to the right from the “O”
(Off) position. There are four blower
speeds.

Temperature Control

Use this control to regulate the tem-
perature of the air inside the passenger
compartment. The blue area of the
scale indicates cooler temperatures
while the red area indicates warmer
temperatures.

NOTE:

If your air conditioning performance seems

lower than expected, check the front of the A/C con-
denser (located in front of the radiator) for an accumu-
lation of dirt or insects. Clean with a gentle water spray
from behind the radiator and through the condenser.
Fabric front fascia protectors may reduce airflow to the
condenser, reducing air conditioning performance.

Mode Control (Air Direction)

Use this control to choose from several
patterns of air distribution. You can
select either a primary mode as iden-
tified by the symbols on the control, or
a blend of two of these modes. The
closer the setting is to a particular
symbol, the more air distribution you
receive from that mode.

UNDERSTANDING YOUR INSTRUMENT PANEL

243

4

«
...
243
244
245
246
247
...
»

Summary of Contents for 2008 Avenger




















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2008 Avenger

Brand: Kathrein Pages: 7

Brand: JANE Pages: 21

Brand: kincrome Pages: 6

Brand: Lexus Pages: 369

Brand: Mountain Top Pages: 12

Brand: Mercedes-Benz Pages: 368

Brand: ULTIMATE SPEED Pages: 21

Brand: Mercedes-Benz Pages: 358

Truck Training Model

Brand: WABCO Pages: 56

Brand: VER-MAC Pages: 64

JEEP GL ADIATOR JT TOPPER ROOF RACK

Brand: JCROffroad Pages: 7

IVH-9000-2R440Q

Brand: Vecow Pages: 110

Brand: SNIPER Pages: 2

transit connect 2012

Brand: Ford Pages: 299

Brand: iSimple Pages: 12

Brand: AUTOTECH Pages: 2

2018 GRAND CHEROKEE

Brand: Jeep Pages: 372

Brand: Jeep Pages: 116

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands