manualshive.com logo in svg

Dodge 2008 Avenger, Owner'S Manual

The Dodge 2008 Avenger Owner's Manual is your go-to guide for getting the most out of your vehicle. This comprehensive manual covers everything from maintenance and troubleshooting to important safety information. Download your free copy from manualshive.com and enjoy the peace of mind that comes with knowing your vehicle inside out.

Share
Download
background image

CAUTION!

All wheels must have the same size and type tires.
Unequal tire sizes must not be used. Unequal tire
size may cause failure of the power transfer unit.

PARKING BRAKE

When the parking brake is applied with the
ignition on, the Brake Light in the instrument
cluster will come on.

NOTE:

•

This light, when illuminated with parking brake ap-
plication, shows only that the parking brake is on. It
does not show the degree of brake application.

•

If the light remains on with the parking brake released,
a brake system malfunction is indicated. Have the
brake system serviced by an authorized dealer imme-
diately.

•

If the parking brake is applied while the vehicle is
moving, a chime will sound to alert the driver. The
chime will sound up to 10 times or until the vehicle
has returned to a stop.

Before leaving the vehicle, make sure that the parking
brake is fully applied and the gear selector is in the PARK
position.

To release the parking brake, slightly pull up the handle
while pushing the lock button, and guide the lever
downward to its stop. The brake warning light in the
instrument cluster should go out.

NOTE:

The parking brake lever will not release unless

the lever is pulled up slightly past its applied position.

276

STARTING AND OPERATING

Summary of Contents for 2008 Avenger




















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2008 Avenger

Pacbrake 10475 Installation Manual preview
10475
Brand: Pacbrake Pages: 9
Prorack K383 Fitting Instructions Manual preview
K383
Brand: Prorack Pages: 14
BGS technic 40108 Manual preview
40108
Brand: BGS technic Pages: 5
Oldsmobile 1999 88 Owner'S Manual preview
1999 88
Brand: Oldsmobile Pages: 344
ABL eMH3 Installation Manual preview
eMH3
Brand: ABL Pages: 66
Trailboss QTHD519L Fitting Instructions Manual preview
QTHD519L
Brand: Trailboss Pages: 8
Dakota Digital MCL-7000 Series Quick Start Manual preview
MCL-7000 Series
Brand: Dakota Digital Pages: 2
Volvo 2010 C30 Owner'S Manual preview
2010 C30
Brand: Volvo Pages: 284
Subaru 360 Sedan Service Manual preview
360 Sedan
Brand: Subaru Pages: 16
Magneti Marelli 350203061230 Installation Instruction preview
350203061230
Brand: Magneti Marelli Pages: 2
Motoalliance Denali MA11705 Manual preview
Denali MA11705
Brand: Motoalliance Pages: 5
Bestop 51252 Installation Instructions preview
51252
Brand: Bestop Pages: 4
Prime Design URX-001-E Assembly Instructions Manual preview
URX-001-E
Brand: Prime Design Pages: 8
Curtis 1POLXP1000GS Installation & Owner'S Manual preview
1POLXP1000GS
Brand: Curtis Pages: 5
ICON 58990 Owner'S Manual & Safety Instructions preview
58990
Brand: ICON Pages: 4
Kargo Master 4090L Instruction Manual preview
4090L
Brand: Kargo Master Pages: 10
AL-KO 605 363 Operating Instructions Manual preview
605 363
Brand: AL-KO Pages: 88
NavLinkz RL4-MIB3-E Manual preview
RL4-MIB3-E
Brand: NavLinkz Pages: 24

Brands by name

Popular brands

Load more brands