manualshive.com logo in svg

Dodge 2008 Avenger, Owner'S Manual

The Dodge 2008 Avenger Owner's Manual is your go-to guide for getting the most out of your vehicle. This comprehensive manual covers everything from maintenance and troubleshooting to important safety information. Download your free copy from manualshive.com and enjoy the peace of mind that comes with knowing your vehicle inside out.

Share
Download
background image

NOTE:

Remember that everything put into or on the

trailer adds to the load on your vehicle. Also, additional
factory-installed options, or authorized dealer-installed
options, must be considered as part of the total load on
your vehicle. Refer to the Tire and Loading Information
placard in the Tire Safety Information Section of this
manual for the maximum combined weight of occupants
and cargo for your vehicle.

CAUTION!

Incorrect trailer tongue weight could result in in-
creased yaw or vehicle instability. A negative trailer
tongue weight could unload the rear suspension of
the tow vehicle decreasing vehicle stability. Negative
trailer tongue weight could cause the trailer to squat
and potentially become disengaged from the tow
vehicle resulting in a runaway trailer condition.

Towing Requirements

To promote proper break-in of your new vehicle driv-
etrain components the following guidelines are recom-
mended:

CAUTION!

•

Avoid towing a trailer for the first 500 mi (805 km)
of vehicle operation. Doing so may damage your
vehicle.

•

During the first 500 mi (805 km) of trailer towing,
limit your speed to 50 mph (80 km/h).

Perform the maintenance listed in Section 8 of this
manual. When towing a trailer, never exceed the GAWR,
or GCWR, ratings.

STARTING AND OPERATING

339

5

Summary of Contents for 2008 Avenger




















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2008 Avenger

Camoplast T4S User Manual preview
T4S
Brand: Camoplast Pages: 60
Whispbar K783W Fitting Instructions Manual preview
K783W
Brand: Whispbar Pages: 16
IBASE Technology MPT-3000V User Manual preview
MPT-3000V
Brand: IBASE Technology Pages: 100
Modifry Products S2000 Windscreen Camera Mount Quick Start Manual preview
S2000 Windscreen Camera Mount
Brand: Modifry Products Pages: 2
Yuasa SmartShot Automatic 12V 1.5 Amp 5 Stage Technical Manual preview
SmartShot Automatic 12V 1.5 Amp 5 Stage
Brand: Yuasa Pages: 44
Thule CIRCUIT 526XT Manual preview
CIRCUIT 526XT
Brand: Thule Pages: 12
Volvo 1996 960 Quick Tips preview
1996 960
Brand: Volvo Pages: 10
Whispbar K951W Fitting Instructions For Basic Carrier preview
K951W
Brand: Whispbar Pages: 15
Vauxhall Meriva 2014 Infotainment Manual preview
Meriva 2014
Brand: Vauxhall Pages: 131
Zap XEBRA ZAPCAR Series Owner'S Manual preview
XEBRA ZAPCAR Series
Brand: Zap Pages: 16
Hama 00 123530 Operating Instructions preview
00 123530
Brand: Hama Pages: 4
Volvo 1992 850 Service And Repair Manual preview
1992 850
Brand: Volvo Pages: 230
BMW 323Ci Manual preview
323Ci
Brand: BMW Pages: 189
RHOX LGT-381L Installation Instructions Manual preview
LGT-381L
Brand: RHOX Pages: 8
Abrams RE-47X Installation And Operation Manual preview
RE-47X
Brand: Abrams Pages: 12
Alphasonik PCP15LDE Owner'S Manual preview
PCP15LDE
Brand: Alphasonik Pages: 8
Toyota Solara guide Owner'S Manual preview
Solara guide
Brand: Toyota Pages: 497
Enduro EM203 User Manual preview
EM203
Brand: Enduro Pages: 52

Brands by name

Popular brands

Load more brands