manualshive.com logo in svg

Dodge 2008 Avenger, Owner'S Manual

The Dodge 2008 Avenger Owner's Manual is your go-to guide for getting the most out of your vehicle. This comprehensive manual covers everything from maintenance and troubleshooting to important safety information. Download your free copy from manualshive.com and enjoy the peace of mind that comes with knowing your vehicle inside out.

Share
Download
background image

indicator system is duty cycle based, which means the
engine oil change interval may fluctuate dependent upon
your personal driving style.

Unless reset, this message will continue to display each
time you turn the ignition switch to the “ON” position.
To turn off the message temporarily, press and release the
Trip Odometer button on the instrument cluster. To reset
the oil change indicator system (after performing the
scheduled maintenance) perform the following proce-
dure:

1. Turn the ignition switch to the “ON” position (Do
not start the engine).

2. Fully depress the accelerator pedal slowly three
times within 10 seconds.

3. Turn the ignition switch to the LOCK position.

NOTE:

If the indicator message illuminates when you

start the vehicle, the oil change indicator system did not
reset. If necessary repeat this procedure.

16. Cruise Indicator — If Equipped

This indicator shows that the Speed Control
System is ON.

17. Odometer/Trip Odometer Reset Knob

Single Trip Odometer
Press and release this button to change the display from
odometer to trip odometer. The word “Trip” displays to
show that the odometer is in Trip Mode. Press and release
the button again to change the display back to the
odometer.

To reset the trip odometer, first set the display to Trip
Mode. Then push and hold the button (approximately 2
seconds) until the display resets to 0. The odometer must
be in Trip Mode to reset the trip odometer.

174

UNDERSTANDING YOUR INSTRUMENT PANEL

Summary of Contents for 2008 Avenger




















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2008 Avenger

GMC SIERRA 2019 Getting To Know Your preview
SIERRA 2019
Brand: GMC Pages: 20
Lincoln 2015 MKS Owner'S Manual preview
2015 MKS
Brand: Lincoln Pages: 424
Volkswagen 1983 Camper Onwers Manual preview
1983 Camper
Brand: Volkswagen Pages: 26
FormFit HD 23A 07 Installation Instructions preview
HD 23A 07
Brand: FormFit Pages: 4
Yakima Whispbar K887W Fitting Instructions Manual preview
Whispbar K887W
Brand: Yakima Pages: 19
Nav TV UCI-11C NTV-KIT331 User Manual preview
UCI-11C NTV-KIT331
Brand: Nav TV Pages: 4
hc-cargo 171850 Mounting And Operation Instructions preview
171850
Brand: hc-cargo Pages: 60
Toro 137-1019 Installation Instructions Manual preview
137-1019
Brand: Toro Pages: 24
Caltrend BM110 Installation Instructions preview
BM110
Brand: Caltrend Pages: 2
Advanced ICE 1296-1 Manual preview
1296-1
Brand: Advanced ICE Pages: 4
Hyundai Santa Fe 2019 Getting Started Manual preview
Santa Fe 2019
Brand: Hyundai Pages: 18
GARO Wallbox GLB Quick Start Manual preview
Wallbox GLB
Brand: GARO Pages: 15
ECS FIA-030-B Fitting Instructions preview
FIA-030-B
Brand: ECS Pages: 4
Whispbar WB751 Manual preview
WB751
Brand: Whispbar Pages: 15
BraunAbility Rampvan Maintenance And Service Manual preview
Rampvan
Brand: BraunAbility Pages: 46
Cadillac Escalade 2004 Escalade ESV Owner'S Manual preview
Escalade 2004 Escalade ESV
Brand: Cadillac Pages: 472
Green Valley 601951 Instructions Manual preview
601951
Brand: Green Valley Pages: 17
Navman N-series B2+ User Manual preview
N-series B2+
Brand: Navman Pages: 27

Brands by name

Popular brands

Load more brands