Dodge 2008 Avenger Owner'S Manual Download Page 19 | Manualshive

Page: 19 / 467

background image

3. Insert the second valid key into the ignition switch.
Turn the ignition switch to the ON position within 15
seconds. After 10 seconds, a chime will sound. In addi-
tion, the Vehicle Security Light will begin to flash. Turn
the ignition switch to the LOCK position and remove the
second key.

4. Insert a blank Sentry Key

t

into the ignition switch.

Turn the ignition switch to the ON position within 60
seconds. After 10 seconds, a single chime will sound. In
addition, the Vehicle Security Light will stop flashing. To
indicate that programming is complete, the Vehicle Secu-
rity Light will turn on again for three seconds and then
turn off.

The new Sentry Key

t

is programmed. The Remote

Keyless Entry (RKE) transmitter will also be pro-
grammed during this procedure.

Repeat this procedure to program up to eight keys. If you
do not have a programmed Sentry Key

t

, contact your

authorized dealer for details.

NOTE:

If a programmed key is lost, see your authorized

dealer to have all remaining keys erased from the sys-
tem’s memory. This will prevent the lost key from
starting your vehicle. The remaining keys must then be
reprogrammed. All vehicle keys must be taken to an
authorized dealer at the time of service to be repro-
grammed.

General Information

The Sentry Key

t

system complies with FCC rules Part 15

and with RSS-210 of Industry Canada. Operation is
subject to the following conditions:

•

This device may not cause harmful interference.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

17

2

«
...
17
18
19
20
21
...
»

Summary of Contents for 2008 Avenger




















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2008 Avenger

Brand: VanEssa mobilcamping Pages: 8

Brand: Porsche Pages: 51

Brand: Whispbar Pages: 14

Brand: Rola Pages: 3

MAGNUM RT Series

Brand: Raptor Series Pages: 6

Brand: Cadillac Pages: 20

Brand: Fiat Pages: 24

Brand: Valeo Pages: 28

Brand: Cadillac Pages: 20

Brand: Kargo Master Pages: 19

PRIME DESIGN VBR3-FT31B

Brand: Safe Fleet Pages: 12

2011 SRX CROSSOVER

Brand: Cadillac Pages: 416

Brand: TIE DOWN Pages: 2

Brand: Edelbrock Pages: 2

Brand: Saab Pages: 288

TOUR EASY 4 936550

Brand: Reimo Pages: 4

Brand: Kargo Master Pages: 17

Aura Mobile BT MCP-2014

Brand: Spracht Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands