manualshive.com logo in svg

Dodge 2008 Avenger, Owner'S Manual

The Dodge 2008 Avenger Owner's Manual is your go-to guide for getting the most out of your vehicle. This comprehensive manual covers everything from maintenance and troubleshooting to important safety information. Download your free copy from manualshive.com and enjoy the peace of mind that comes with knowing your vehicle inside out.

Share
Download
background image

If you must use the accessories (wipers, defrosters, etc.)
while being towed, the key must be in the ON position,
not the ACC position. Make certain the transaxle remains
in NEUTRAL.

TOWING WITHOUT THE IGNITION KEY

Special care must be taken when the vehicle is towed
with the ignition in the LOCK position. Flat bed towing
is the preferred towing method. However, if a flat bed
towing vehicle is not available, a wheel lift towing
vehicle may be used. Furthermore, rear towing is not
recommended with the front wheels on the ground, as
transaxle damage can result. If rear towing is the only
alternative, a front end dolly must be used. Proper
towing equipment is necessary to prevent damage to the
vehicle.

TOWING THIS VEHICLE BEHIND ANOTHER
VEHICLE

Flat towing with all four wheels on the ground of
vehicles equipped with an automatic transmission, is
only permitted within the limitations described in this
section.

TOWING THIS VEHICLE BEHIND ANOTHER
VEHICLE WITH A TOW DOLLY

Rear towing is not recommended with the front wheels
on the ground, as transaxle damage can result. If rear
towing is the only alternative, a front end dolly must be
used. Proper towing equipment is necessary to prevent
damage to the vehicle.

WHAT TO DO IN EMERGENCIES

363

6

Summary of Contents for 2008 Avenger




















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2008 Avenger

kaarta STENCIL PRO Assembly & Use preview
STENCIL PRO
Brand: kaarta Pages: 29
Toyota 2016 RAV4 Quick Reference Manual preview
2016 RAV4
Brand: Toyota Pages: 56
Genesis Multiple G9F18 AU000 Quick Start Manual preview
Multiple G9F18 AU000
Brand: Genesis Pages: 3
Compass 02106 Manual preview
02106
Brand: Compass Pages: 16
Honda 2011 Civic Sedan Vehicle Instruction Card preview
2011 Civic Sedan
Brand: Honda Pages: 5
Suzuki 990E0-54P56-000 Installers And Users Instructions preview
990E0-54P56-000
Brand: Suzuki Pages: 12
Scosche BTFREQ PRO BTFMPD3SR Manual preview
BTFREQ PRO BTFMPD3SR
Brand: Scosche Pages: 16
Kia Sorento Owner'S Manual preview
Sorento
Brand: Kia Pages: 51
PEUGEOT 108 2017 Vehicle Instruction Card preview
108 2017
Brand: PEUGEOT Pages: 17
cam 40103 AL Mounting Instructions preview
40103 AL
Brand: cam Pages: 6
Rostra RearSight 250-8308 Installation Instructions preview
RearSight 250-8308
Brand: Rostra Pages: 2
Volvo 31339699 Installation Instructions, Accessories preview
31339699
Brand: Volvo Pages: 18
Uniden BTSC1100 Owner'S Manual preview
BTSC1100
Brand: Uniden Pages: 16
A-Tach Mounts 50321 Quick Start Manual preview
50321
Brand: A-Tach Mounts Pages: 2
Thule 2087 Parts List preview
2087
Brand: Thule Pages: 1
Waeco MagicWatch MWE150 Installation And Operating Manual preview
MagicWatch MWE150
Brand: Waeco Pages: 176
chinavasion CVTM-C163 User Manual preview
CVTM-C163
Brand: chinavasion Pages: 3
Mini COOPER Convertible Owner'S Manual preview
COOPER Convertible
Brand: Mini Pages: 168

Brands by name

Popular brands

Load more brands