Dodge 2008 Avenger Owner'S Manual Download Page 149 | Manualshive

Page: 149 / 467

background image

NOTE:

There are 30 seconds in which to initiate the next

step after the “Learn” button has been pressed.

7. Return to the vehicle and press the programmed
HomeLink

t

button twice (holding the button for two

seconds each time). If the device is plugged in and
activates, programming is complete.

If the device does not activate, press the button a third
time (for two seconds) to complete the training.

If you have any problems, or require assistance, please
call toll-free 1–800–355–3515 or, on the Internet at
www.HomeLink.com for information or assistance.

To program the remaining two HomeLink

t

buttons,

repeat each step for each remaining button. DO NOT
erase the channels.

Using HomeLink

t

To operate, simply press and release the programmed
HomeLink

t

button. Activation will now occur for the

trained device (i.e., garage door opener, gate operator,
security system, entry door lock, home/office lighting,
etc. The hand-held transmitter of the device may also be
used at any time.

Reprogramming a Single Homelink

t

Button

To reprogram a channel that has been previously trained,
follow these steps:

1. Turn the ignition switch to the ON/RUN position.

2. Press and hold the desired HomeLink

t

button until

the indicator light begins to flash after 20 seconds. Do not
release the button.

3. Without releasing the button, proceed with Program-
ming Homelink

t

Step 2 and follow all remaining steps.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

147

3

«
...
147
148
149
150
151
...
»

Summary of Contents for 2008 Avenger




















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2008 Avenger

Brand: Mazda Pages: 4

Brand: ZAPTEC Pages: 64

Brand: ZAPTEC Pages: 24

Brand: Jabra Pages: 10

Brand: Mazda Pages: 13

Impala Limited 2014

Brand: Chevrolet Pages: 356

Brand: Kia Pages: 11

Brand: Saab Pages: 426

Brand: travall Pages: 2

Brand: Gacell Pages: 12

Brand: Subaru Pages: 298

ESCALADE ESV 2005

Brand: Cadillac Pages: 482

Brand: curt Pages: 4

Brand: Dakota Digital Pages: 20

Brand: TATA Motors Pages: 308

Brand: Scosche Pages: 12

Brand: Gentex Pages: 2

Brand: CARFACE Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands