manualshive.com logo in svg

Dodge 2008 Avenger, Owner'S Manual

The Dodge 2008 Avenger Owner's Manual is your go-to guide for getting the most out of your vehicle. This comprehensive manual covers everything from maintenance and troubleshooting to important safety information. Download your free copy from manualshive.com and enjoy the peace of mind that comes with knowing your vehicle inside out.

Share
Download
background image

SPARK PLUGS

Spark plugs must fire properly to assure engine perfor-
mance and emission control. New plugs should be in-
stalled at the specified mileage. The entire set should be
replaced if there is any malfunction due to a faulty spark
plug. Refer to “Fluids, Lubricants, and Genuine Parts” in
this section for the proper type of spark plug for use in
your vehicle.

ENGINE AIR CLEANER FILTER

Refer to the “Maintenance Schedule” in Section 8 of this
manual for engine air cleaner filter maintenance inter-
vals.

NOTE:

Be sure to follow the “dusty or off-road condi-

tions” maintenance interval if applicable.

WARNING!

The air induction system (air cleaner, hoses, etc.) can
provide a measure of protection in the case of engine
backfire. Do not remove the air induction system (air
cleaner, hoses, etc.) unless such removal is necessary
for repair or maintenance. Make sure that no one is
near the engine compartment before starting the
vehicle with the air induction system (air cleaner,
hoses, etc.) removed. Failure to do so can result in
serious personal injury.

CATALYTIC CONVERTER

The catalytic converter requires the use of unleaded fuel
only. Leaded gasoline will destroy the effectiveness of the
catalyst as an emission control device.

MAINTAINING YOUR VEHICLE

379

7

Summary of Contents for 2008 Avenger




















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2008 Avenger

Mazda 2011 Tribute Brochure & Specs preview
2011 Tribute
Brand: Mazda Pages: 4
UMBRA RIMORCHI 39030 Installation Instructions Manual preview
39030
Brand: UMBRA RIMORCHI Pages: 18
Mazda 2012 Mazda6 Owner'S Manual preview
2012 Mazda6
Brand: Mazda Pages: 527
Cadillac 2008 Escalade EXT Owner'S Manual preview
2008 Escalade EXT
Brand: Cadillac Pages: 496
Porsche 911 GT3 - Owner'S Manual preview
911 GT3 -
Brand: Porsche Pages: 195
BMW M5 2014 Service And Warranty Information preview
M5 2014
Brand: BMW Pages: 38
Easee Home Wallbox Installation Instructions Manual preview
Home Wallbox
Brand: Easee Pages: 12
Meta System 900000358 Installation Technical Sheet preview
900000358
Brand: Meta System Pages: 22
Havis-Shields 1996-2008 Crown Victoria Driver and Passenger - Trunk Side Mounts C-TSM-CV-P Datasheet preview
1996-2008 Crown Victoria Driver and Passenger - Trunk Side Mounts C-TSM-CV-P
Brand: Havis-Shields Pages: 1
Mercedes-Benz Vito Taxi 2011 Operation Manual preview
Vito Taxi 2011
Brand: Mercedes-Benz Pages: 10
Edelbrock 5756 Installation Instructions preview
5756
Brand: Edelbrock Pages: 1
Acura TSX 2014 Advanced Technology Manual preview
TSX 2014
Brand: Acura Pages: 19
Ford 2009 Edge Owner'S Manual preview
2009 Edge
Brand: Ford Pages: 325
CITROEN 1953 Traction Avant User Manual preview
1953 Traction Avant
Brand: CITROEN Pages: 26
Whispbar K723W Fitting Instructions Manual preview
K723W
Brand: Whispbar Pages: 77
Honda 2000 RL Owner'S Manual preview
2000 RL
Brand: Honda Pages: 330
Painless Performance VORTEC 60211 Installation Instructions Manual preview
VORTEC 60211
Brand: Painless Performance Pages: 16
EUFAB 11439 Assembly preview
11439
Brand: EUFAB Pages: 8

Brands by name

Popular brands

Load more brands