Dodge 2008 Avenger Owner'S Manual Download Page 40 | Manualshive

Page: 40 / 467

background image

WINDOW LOCKOUT SWITCH

The window lockout switch on the driver’s door allows
you to disable the window control on the other doors. To
disable the window controls on the other doors, press the
window lock button. To enable the window controls,
press the window control button again.

WIND BUFFETING

Wind buffeting can be described as the perception of
pressure on the ears or a helicopter type sound in the
ears. Your vehicle may exhibit wind buffeting with the
windows down, or the sunroof (if equipped) in certain
open or partially open positions. This is a normal occur-
rence and can be minimized. If the buffeting occurs with
the rear windows open, then open the front and rear
windows together to minimize the buffeting. If the
buffeting occurs with the sunroof open, then adjust the
sunroof opening to minimize the buffeting.

Window Lockout Switch

38

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

«
...
38
39
40
41
42
...
»

Summary of Contents for 2008 Avenger




















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2008 Avenger

Brand: ZAPTEC Pages: 240

Brand: Condor Pages: 2

Xplore Pro II SxS

Brand: Marlon Pages: 15

Brand: Cadillac Pages: 368

Brand: Luverne Pages: 3

Brand: Navman Pages: 27

Brand: Fab Fours Pages: 13

Brand: Yakima Pages: 12

Brand: Axxess Pages: 16

Brand: Honda Pages: 569

Brand: Mazda Pages: 3

Airgo Active cushion / Comfort

Brand: TOGU Pages: 2

Brand: Maserati Pages: 37

Brand: Mazda Pages: 7

Brand: WABCO Pages: 40

Brand: Thule Pages: 8

Brand: VDO Pages: 6

Cutlass 1978 Series

Brand: Oldsmobile Pages: 97

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands