Dodge 2008 Avenger Owner'S Manual Download Page 117 | Manualshive

Page: 117 / 467

background image

General Information

This device complies with Part 15 of the FCC rules and
RSS 210 of Industry Canada. Operation is subject to the
following conditions:

•

This device may not cause harmful interference.

•

This device must accept any interference received,
including interference that may cause undesired op-
eration.

VOICE RECOGNITION SYSTEM — IF EQUIPPED

Voice Recognition System (VR) Operation

This Voice Recognition System allows you to
control your AM, FM radio, satellite radio, disc
player, and a memo recorder.

NOTE:

In a stressful situation, take care to speak into

the Voice Interface System as calmly and normally as
possible. The ability of the Voice Interface System to

recognize user voice commands may be negatively af-
fected by rapid speaking or a raised voice level.

WARNING!

Any voice commanded system should be used only
in safe driving conditions and all attention should be
kept on the roadway ahead. Failure to do so may
result in an accident causing serious injury or death.

When you press the VR hard-key, you will hear a beep.
The beep is your signal to give a command.

NOTE:

If you do not say a command within a few

seconds, the system will present you with a list of
options.

If you ever wish to interrupt the system while it lists
options, press the VR hard-key, listen for the beep, and
say your command.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

115

3

«
...
115
116
117
118
119
...
»

Summary of Contents for 2008 Avenger




















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2008 Avenger

Brand: Jeep Pages: 12

Brand: Jeep Pages: 6

Brand: BGS technic Pages: 5

Brand: Oldsmobile Pages: 344

Brand: ABL Pages: 66

2010 Civic Sedan

Brand: Honda Pages: 390

Brand: HAUL MASTER Pages: 8

Brand: Mini Pages: 20

Brand: Right Weigh Pages: 16

Brand: Cadillac Pages: 20

Brand: Fab Fours Pages: 21

PRIME DESIGN HRR-369-E-UM3-96

Brand: Safe Fleet Pages: 12

Brand: Kocchi's Pages: 4

Brand: ULTIMATE SPEED Pages: 34

Brand: Abrams Pages: 12

2003 Silhouette

Brand: Oldsmobile Pages: 466

Brand: Pontiac Pages: 486

Brand: Westfalia Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands