manualshive.com logo in svg

Dodge 2008 Avenger, Owner'S Manual

The Dodge 2008 Avenger Owner's Manual is your go-to guide for getting the most out of your vehicle. This comprehensive manual covers everything from maintenance and troubleshooting to important safety information. Download your free copy from manualshive.com and enjoy the peace of mind that comes with knowing your vehicle inside out.

Share
Download
background image

WARNING!

If the hood is not fully latched it could fly up when
the vehicle is moving and block your forward vision.
You could have a collision. Be sure all hood latches
are fully latched before driving.

LIGHTS

MAP/READING/INTERIOR LIGHTS

These lights are mounted between the sun visors above
the rear view mirror. Each light is turned ON by pressing
the button. Press the button a second time to turn the
light OFF. The lights will remain on until the switch is
pressed a second time, so be sure they have been turned
off before leaving the vehicle. They will not turn off
automatically. Interior lighting also comes on when a
door is opened or the dimmer control is turned fully
upward, past the second detent.

There is a second light located midway back in the
headliner.

To protect the battery, the interior lights will turn off
automatically 10 minutes after the ignition switch is
moved to the LOCK position. This will occur if the
interior lights were switched on manually or are on

Interior Dome Lamp

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

129

3

Summary of Contents for 2008 Avenger




















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2008 Avenger

CAMPARK R10 Manual preview
R10
Brand: CAMPARK Pages: 20
GARO TWIN+ Assembly Instructions / End User Instruction preview
TWIN+
Brand: GARO Pages: 23
GARO LS4 Wallmounted Operational Instructions preview
LS4 Wallmounted
Brand: GARO Pages: 15
Bimmer Jakes FRONT HEADLIGHT LENS COVER Replacement Manual preview
FRONT HEADLIGHT LENS COVER
Brand: Bimmer Jakes Pages: 4
Kia CADENZA 2019 Features & Functions Manual preview
CADENZA 2019
Brand: Kia Pages: 54
Metra Electronics 99-9001 Installation Instructions preview
99-9001
Brand: Metra Electronics Pages: 2
Ironton 44596 Owner'S Manual preview
44596
Brand: Ironton Pages: 7
Dacia 2014 Sandero Driver'S Handbook Manual preview
2014 Sandero
Brand: Dacia Pages: 238
Raptor Series MAGNUM RT Series Manual preview
MAGNUM RT Series
Brand: Raptor Series Pages: 6
Porsche 01-B Web Application Manual preview
01-B
Brand: Porsche Pages: 313
Cadillac 54-6219 1954 Shop Manual preview
54-6219 1954
Brand: Cadillac Pages: 409
Fortin THAR-AUD1 Manual preview
THAR-AUD1
Brand: Fortin Pages: 9
Westfalia 305 158 Mounting Instructions preview
305 158
Brand: Westfalia Pages: 10
DriveRight 8156OBD Installation Manual preview
8156OBD
Brand: DriveRight Pages: 16
Improved Racing E5G-601 Instructions Manual preview
E5G-601
Brand: Improved Racing Pages: 17
Cadillac 2004 Seville Customer Convenience/Personalization Manual preview
2004 Seville
Brand: Cadillac Pages: 20
Pyle PLRD146 User Manual preview
PLRD146
Brand: Pyle Pages: 8
Yakima Landing Pad 11 Manual preview
Landing Pad 11
Brand: Yakima Pages: 28

Brands by name

Popular brands

Load more brands