Dodge 2008 Avenger Owner'S Manual Download Page 144 | Manualshive

Page: 144 / 467

background image

To Vary Speed Setting:

When the speed control is ON, speed can be increased by
pushing up and holding RESUME ACCEL. Release the
lever when the desired speed is reached, and the new
speed will be set.

Pushing up and quickly releasing the RESUME ACCEL
lever will result in a 1 mph (2 km/h) speed increase. Each
time the lever is pushed upwards and quickly released.

To decrease speed while speed control is ON, push down
and hold SET DECEL. Release the lever when the desired
speed is reached, and the new speed will be set.

Pushing down the SET DECEL button once will result in
a 1 mph (2 km/h) speed decrease. Each time the button is
pushed, speed decreases.

WARNING!

Speed Control can be dangerous where the system
can’t maintain a constant speed. Your vehicle could
go too fast for the conditions, and you could lose
control. An accident could be the result. Don’t use
Speed Control in heavy traffic or on roads that are
winding, icy, snow-covered, or slippery.

To Accelerate For Passing:

Depress the accelerator as you would normally. When the
pedal is released, the vehicle will return to the set speed.

Using Speed Control on Hills

NOTE:

The speed control system maintains speed up

and down hills. A slight speed change on moderate hills
is normal.

142

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

«
...
142
143
144
145
146
...
»

Summary of Contents for 2008 Avenger




















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2008 Avenger

Brand: Jeep Pages: 6

Brand: EAL Pages: 4

Brand: Van Guard Pages: 3

Calispace Ocean 80

Brand: Calitop Pages: 5

Evo All THAR-FOR3

Brand: Fortin Pages: 7

Brand: Kuda Pages: 2

Brand: Xhorse Pages: 48

Brand: Metra Electronics Pages: 8

TRI-FOLD PG9300RF

Brand: Pet Gear Pages: 4

Brand: travall Pages: 2

Brand: Gacell Pages: 12

Brand: SNIPER Pages: 2

PRIME DESIGN HRR-369-E-UM3-96

Brand: Safe Fleet Pages: 12

Brand: Kocchi's Pages: 4

Brand: Oldsmobile Pages: 358

CERTA CTCVINCVR14A

Brand: Kogan Pages: 4

Brand: Toyota Pages: 295

Brand: Oldsmobile Pages: 276

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands