manualshive.com logo in svg

Dodge 2008 Avenger, Owner'S Manual

The Dodge 2008 Avenger Owner's Manual is your go-to guide for getting the most out of your vehicle. This comprehensive manual covers everything from maintenance and troubleshooting to important safety information. Download your free copy from manualshive.com and enjoy the peace of mind that comes with knowing your vehicle inside out.

Share
Download
background image

WARNING!

Improper towing can lead to an injury accident.
Follow these guidelines to make your trailer towing
as safe as possible:

Make certain that the load is secured in the trailer
and that it will not shift during travel. When traile-
ring cargo that is not fully secured, dynamic load
shifts can occur that may be difficult for the driver to
control. You could lose control of your vehicle and
have an accident.

•

When hauling cargo, or towing a trailer, do not
overload your vehicle or trailer. Overloading can cause
a loss of control, poor performance, or damage to
brakes, axle, engine, transaxle, steering, suspension,
chassis structure, or tires.

•

Safety chains must always be used between your
vehicle and trailer. Always connect the chains to the
frame or hook retainers of the vehicle hitch. Cross the
chains under the trailer tongue and allow enough
slack for turning corners.

•

Vehicles with trailers should not be parked on a grade.
When parking, apply the parking brake on the tow
vehicle. Put the tow vehicle automatic transaxle in
PARK. Always, block or

9

chock

9

the trailer wheels.

•

GCWR must not be exceeded.

•

Total weight must be distributed between the tow
vehicle and the trailer such that the following four
ratings are not exceeded:

1. GVWR

2. GTW

3. GAWR

340

STARTING AND OPERATING

Summary of Contents for 2008 Avenger




















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2008 Avenger

GMC YUKON 2018 Owner'S Manual preview
YUKON 2018
Brand: GMC Pages: 425
Hama 00201510 Operating Instructions Manual preview
00201510
Brand: Hama Pages: 40
BMW 01 29 9 416 497 Installation Instructions preview
01 29 9 416 497
Brand: BMW Pages: 5
CTEK D250S Dual Manual preview
D250S Dual
Brand: CTEK Pages: 84
tams elektronik FCS-4 Manual preview
FCS-4
Brand: tams elektronik Pages: 19
Valeo Park Vision VAL632210 Instruction Manual preview
Park Vision VAL632210
Brand: Valeo Pages: 25
Black Horse Off Road TO20 Installation Instructions Manual preview
TO20
Brand: Black Horse Off Road Pages: 7
v.link VL2-MBN2 Manual preview
VL2-MBN2
Brand: v.link Pages: 12
Saab 32 025 603 Installation Instructions Manual preview
32 025 603
Brand: Saab Pages: 15
Yakima K896 Instructions Manual preview
K896
Brand: Yakima Pages: 12
Ecco Nova Electronics Hide-a-Led DEUCE DUAL HEAD W600 Manual preview
Nova Electronics Hide-a-Led DEUCE DUAL HEAD W600
Brand: Ecco Pages: 2
Quadratec QuadraTop Adventure Top 1113.00 Series Installation Manual preview
QuadraTop Adventure Top 1113.00 Series
Brand: Quadratec Pages: 20
Bracketron MULTI VEHICLE MOUNT MVM-45-05 Installation Manual preview
MULTI VEHICLE MOUNT MVM-45-05
Brand: Bracketron Pages: 4
Parkmate RVM-043DVR User Manual preview
RVM-043DVR
Brand: Parkmate Pages: 16
Honda 2014 Accord Sedan Reference Manual preview
2014 Accord Sedan
Brand: Honda Pages: 24
DV8 FBBR-03 Installation Manual preview
FBBR-03
Brand: DV8 Pages: 11
Kia Cerato 2021 Manual preview
Cerato 2021
Brand: Kia Pages: 714
Hamron 001677 Operating Instructions preview
001677
Brand: Hamron Pages: 5

Brands by name

Popular brands

Load more brands