manualshive.com logo in svg

Dodge 2008 Avenger, Owner'S Manual

The Dodge 2008 Avenger Owner's Manual is your go-to guide for getting the most out of your vehicle. This comprehensive manual covers everything from maintenance and troubleshooting to important safety information. Download your free copy from manualshive.com and enjoy the peace of mind that comes with knowing your vehicle inside out.

Share
Download
background image

Press and hold the INFO button again for three seconds
to return to

9

elapsed time

9

display.

Operation Instructions - Auxiliary Mode
The auxiliary (AUX) jack is an audio input jack, which
allows the user to plug in a portable device such as an
MP3 player, or cassette player, and utilize the vehicle’s
audio system to amplify the source and play through the
vehicle speakers.

Pressing the AUX button will change the mode to auxil-
iary device if the AUX jack is connected.

NOTE:

The AUX device must be turned on and the

device’s volume set to proper level. If the AUX audio is
not loud enough, turn the device’s volume up. If the AUX
audio sounds distorted, turn the device’s volume down.

TIME Button (Auxiliary Mode)
Press this button to change the display to time of day. The
time of day will display for five seconds (when ignition is
OFF).

Operating Instructions - Hands-Free Phone
(UConnect

t

) (If Equipped)

Refer to “Hands-Free Communication (UConnect

t

)” in

Section 3.

Operating Instructions - Satellite Radio Mode (If
Equipped)
Refer to “Satellite Radio” in this section.

Operating Instructions - Video Entertainment
System (VES)

t

(If Equipped)

Refer to separate “Video Entertainment System (VES)

t

Guide.”

204

UNDERSTANDING YOUR INSTRUMENT PANEL

Summary of Contents for 2008 Avenger




















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2008 Avenger

Quadratec Brute Strength 12057.0271 Installation Manual preview
Brute Strength 12057.0271
Brand: Quadratec Pages: 6
Caltrend CV445 Installation Instructions preview
CV445
Brand: Caltrend Pages: 2
Audiovox EM-2201 Installation Instructions preview
EM-2201
Brand: Audiovox Pages: 1
EGR EGR-3PVE-COLOUR Installation Instructions Manual preview
EGR-3PVE-COLOUR
Brand: EGR Pages: 28
VDO DLD Wide Range II Installation Instructions Manual preview
DLD Wide Range II
Brand: VDO Pages: 84
Wagan TravelCharge Companion GO-Plus User Manual preview
TravelCharge Companion GO-Plus
Brand: Wagan Pages: 3
Monacor Carpower CAP-20 Quick Manual preview
Carpower CAP-20
Brand: Monacor Pages: 2
Dodge Dodge Challenger SRT8®Challenger SRT8 392 2012 Specifications preview
Dodge Challenger SRT8®Challenger SRT8 392 2012
Brand: Dodge Pages: 5
Edelbrock 65932 Installation Instructions preview
65932
Brand: Edelbrock Pages: 2
Safe Fleet PRIME DESIGN HRR-369-E-UM3-96 Manual preview
PRIME DESIGN HRR-369-E-UM3-96
Brand: Safe Fleet Pages: 12
Kocchi's 772161M1 Manual preview
772161M1
Brand: Kocchi's Pages: 4
Oldsmobile 1998 Aurora Owner'S Manual preview
1998 Aurora
Brand: Oldsmobile Pages: 380
Lantronix FOX3 Series Hardware Manual preview
FOX3 Series
Brand: Lantronix Pages: 51
GReddy 12519101 Instruction Manual preview
12519101
Brand: GReddy Pages: 12
TATA Motors Indigo LE Owner'S Manual & Service Book preview
Indigo LE
Brand: TATA Motors Pages: 151
Thule QUICKDRAW RACHET TIE-DOWNS 855 User Manual preview
QUICKDRAW RACHET TIE-DOWNS 855
Brand: Thule Pages: 3
Oldsmobile 1994 Bravada Owner'S Manual preview
1994 Bravada
Brand: Oldsmobile Pages: 248
QA1 GS501 Installation Instructions preview
GS501
Brand: QA1 Pages: 3

Brands by name

Popular brands

Load more brands