manualshive.com logo in svg

Dodge 2008 Avenger, Owner'S Manual

The Dodge 2008 Avenger Owner's Manual is your go-to guide for getting the most out of your vehicle. This comprehensive manual covers everything from maintenance and troubleshooting to important safety information. Download your free copy from manualshive.com and enjoy the peace of mind that comes with knowing your vehicle inside out.

Share
Download
background image

•

Extended use of recirculation may cause the windows
to fog. If the interior of the windows begins to fog,
press the RECIRCULATION button to return to out-
side air. Some temp/humidity conditions will cause
captured interior air to condense on windows and
hamper visibility. For this reason, the system will not
allow Recirculation to be selected while in floor, de-
frost, or defrost/floor mode. Attempting to use the
Recirculation while in these modes will cause the LED
in the CONTROL button to blink and then turn off.

•

Most of the time, when in Automatic Operation, you
can temporarily put the system into Recirculation
mode by pressing the RECIRCULATION button.
However, under certain conditions, while in Auto-
matic Mode, the system is blowing air out the defrost
vents. When these conditions are present, and the
RECIRCULATION button is pressed, the indicator will
flash and then turn off. This tells you that you are
unable to go into recirculation mode at this time. If you

would like the system to go into Recirculation mode,
you must first move the Mode Knob to Panel, Panel/
Floor and then press the RECIRCULATION button.
This feature reduces the possibility of window fog-
ging.

Operating Tips

NOTE:

Refer to the chart at the end of this section for

suggested control settings for various weather condi-
tions.

Summer Operation
The engine cooling system in air-conditioned vehicles
must be protected with a high-quality antifreeze coolant
to provide proper corrosion protection and to protect
against engine overheating. A 50% solution of ethylene
glycol antifreeze coolant in water is recommended. Refer
to “Maintenance Procedures” in Section 7 of this manual
for proper coolant selection.

252

UNDERSTANDING YOUR INSTRUMENT PANEL

Summary of Contents for 2008 Avenger




















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2008 Avenger

Daihatsu TERIOS J100 Maintenance Manual preview
TERIOS J100
Brand: Daihatsu Pages: 43
ABL Wallbox eM4 Single Installation Manual preview
Wallbox eM4 Single
Brand: ABL Pages: 68
Warrior Products 4560 Manual preview
4560
Brand: Warrior Products Pages: 4
John Gold Gold Cruuse Cruisecontrol GC90 Installation Manual preview
Gold Cruuse Cruisecontrol GC90
Brand: John Gold Pages: 24
Whispbar K498W Fitting Instructions Manual preview
K498W
Brand: Whispbar Pages: 14
FALCON RIDGE HO-P500-FC04 Instructions For Installation And Care preview
HO-P500-FC04
Brand: FALCON RIDGE Pages: 8
Scosche 142HUD2 Manual preview
142HUD2
Brand: Scosche Pages: 8
Cadillac 54-6219 1954 Shop Manual preview
54-6219 1954
Brand: Cadillac Pages: 409
Fortin THAR-AUD1 Manual preview
THAR-AUD1
Brand: Fortin Pages: 9
Magneti Marelli 350203061230 Installation Instruction preview
350203061230
Brand: Magneti Marelli Pages: 2
PEUGEOT 108 2017 Vehicle Instruction Card preview
108 2017
Brand: PEUGEOT Pages: 17
Mazda 0000-8L-G03A Installation Instructions preview
0000-8L-G03A
Brand: Mazda Pages: 3
BMW FXX ATM Emulator User And Installation Manual preview
FXX ATM Emulator
Brand: BMW Pages: 5
Cadillac 2011 Cadillac Owner Assistance Information preview
2011 Cadillac
Brand: Cadillac Pages: 48
Vauxhall 2013 Zafira Tourer Owner'S Manual preview
2013 Zafira Tourer
Brand: Vauxhall Pages: 289
Mercedes-Benz SLK 350 Brochure preview
SLK 350
Brand: Mercedes-Benz Pages: 24
ULTIMATE SPEED UKLL 5 A1 Operating Instructions Manual preview
UKLL 5 A1
Brand: ULTIMATE SPEED Pages: 132
Prime Design VRI3-FT31B Assembly Manual preview
VRI3-FT31B
Brand: Prime Design Pages: 16

Brands by name

Popular brands

Load more brands