Dodge 2008 Avenger Owner'S Manual Download Page 16 | Manualshive

Page: 16 / 467

background image

CAUTION!

An unlocked car is an invitation to thieves. Always
remove key from the ignition and lock all doors
when leaving the vehicle unattended.

KEY-IN-IGNITION REMINDER

Opening the driver’s door when the key is in the ignition,
sounds a signal to remind you to remove the key.

NOTE:

•

The Key-In-Ignition reminder only sounds when the
ignition key is placed in the LOCK or ACC position.

•

With either front door open, and the key in the
ignition, both the power door locks and Remote Key-
less Entry (RKE) will not function.

LOCKING DOORS WITH THE KEY

There is only one external door lock cylinder which is
located in the driver’s door only.

You can insert the key with either side up. To lock the
door, turn the key rearward, to unlock the door, turn the
key forward. See Section 7 of this manual for door lock
lubrication.

SENTRY KEY

T

The Sentry Key

t

Immobilizer System prevents unautho-

rized vehicle operation by disabling the engine. The
system does not need to be armed or activated. Operation
is automatic, regardless of whether the vehicle is locked
or unlocked.

The system uses ignition keys that have an embedded
electronic chip (transponder) to prevent unauthorized
vehicle operation. Therefore, only keys that are pro-
grammed to the vehicle can be used to start and operate

14

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

«
...
14
15
16
17
18
...
»

Summary of Contents for 2008 Avenger




















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2008 Avenger

Brand: iDataLink Pages: 106

Brand: Zavoli Pages: 26

Brand: Barker Pages: 2

Wireless Charging Station Universal

Brand: BMW Pages: 160

Quattroporte Automatic

Brand: Maserati Pages: 272

Brand: ULTIMATE SPEED Pages: 21

Brand: Whispbar Pages: 14

Brand: Reese Explore Pages: 9

Brand: iArmor Pages: 6

Brand: Motoalliance Pages: 5

Brand: Honda Pages: 124

Brand: DFI Pages: 6

Brand: Cadillac Pages: 438

Brand: Lexus Pages: 878

Brand: Porsche Pages: 145

Brand: DiscountRamps Pages: 2

Brand: Hopkins Pages: 4

Brand: Masterack Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands