manualshive.com logo in svg

Dodge 2008 Avenger, Owner'S Manual

The Dodge 2008 Avenger Owner's Manual is your go-to guide for getting the most out of your vehicle. This comprehensive manual covers everything from maintenance and troubleshooting to important safety information. Download your free copy from manualshive.com and enjoy the peace of mind that comes with knowing your vehicle inside out.

Share
Download
background image

11. Check the tire pressure as soon as possible. Correct
pressure as required.

JUMP-STARTING PROCEDURES DUE TO A LOW
BATTERY

Jump-starting remote battery terminals are located under
the hood.

The battery is stored between the left front headlight
assembly and the left front wheel splash shield. Access is
through the splash shield.

WARNING!

•

Take care to avoid the radiator cooling fan whenever the
hood is raised. It can start anytime the ignition switch is
on. You can be hurt by the fan.

•

Do not attempt to push or tow your vehicle to get it
started. Vehicles equipped with an automatic transaxle
cannot be started this way. Unburned fuel could enter
the catalytic converter and once the engine has started,
ignite and damage the converter and vehicle. If the
vehicle has a discharged battery, booster cables may be
used to obtain a start from another vehicle. This type of
start can be dangerous if done improperly, so follow this
procedure carefully.

•

Do not use a booster battery or any other booster source
with an output that exceeds 12 volts.

•

During cold weather when temperatures are below
freezing point, electrolyte in a discharged battery may
freeze. Do not attempt jump-starting because the battery
could rupture or explode. The battery temperature must
be brought up above freezing point before attempting
jump-start.

358

WHAT TO DO IN EMERGENCIES

Summary of Contents for 2008 Avenger




















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2008 Avenger

Kargo Master 40640 Assembly Manual preview
40640
Brand: Kargo Master Pages: 5
Yakima K800 Instructions Manual preview
K800
Brand: Yakima Pages: 8
Tesla V2 SUPERCHARGER First Responder'S Manual preview
V2 SUPERCHARGER
Brand: Tesla Pages: 9
Streetwize LeisureWize EMOVE EM303A Manual preview
LeisureWize EMOVE EM303A
Brand: Streetwize Pages: 20
Chevrolet 2013 Spark Specifications preview
2013 Spark
Brand: Chevrolet Pages: 2
Quadratec 12057.0263 Installation Manual preview
12057.0263
Brand: Quadratec Pages: 12
Yakima Prorack K436 Fitting Instructions Manual preview
Prorack K436
Brand: Yakima Pages: 13
walser ULTIMATE SPEED 296713 Assembly And Safety Advice preview
ULTIMATE SPEED 296713
Brand: walser Pages: 10
Mercedes-Benz 2009 E-Class Manual preview
2009 E-Class
Brand: Mercedes-Benz Pages: 373
Subaru 2003 Baja Owner'S Manual preview
2003 Baja
Brand: Subaru Pages: 32
Waeco Magic Watch MWE-850-4DSM Installation And Operating Manual preview
Magic Watch MWE-850-4DSM
Brand: Waeco Pages: 204
Black+Decker BXAE00011 Operating Instructions Manual preview
BXAE00011
Brand: Black+Decker Pages: 21
Beeper RW050RF User& Installer'S Manual preview
RW050RF
Brand: Beeper Pages: 20
Vauxhall Crossland X 2017 Owner'S Manual preview
Crossland X 2017
Brand: Vauxhall Pages: 245
Vauxhall 2013 Ampera Infotainment Manual preview
2013 Ampera
Brand: Vauxhall Pages: 95
Lincoln 2012 MKX Owner'S Manual preview
2012 MKX
Brand: Lincoln Pages: 364
Honda 1993 Civic Coupe Owner'S Manual preview
1993 Civic Coupe
Brand: Honda Pages: 201
X-Armour XR-9500 Installation And Owner'S Manual preview
XR-9500
Brand: X-Armour Pages: 16

Brands by name

Popular brands

Load more brands