Dodge 2008 Avenger Owner'S Manual Download Page 415

Page: 415 / 467

2. Reach into engine compartment and from behind the
lamp assembly and grasp the connector.

3. Rotate bulb and connector

⁄

turn and pull outward

from assembly.

CAUTION!

Do not touch the new bulb with your fingers. Oil
contamination will severely shorten bulb life.

Headlight Housing - Rear View

Twisting Bulb From Socket

MAINTAINING YOUR VEHICLE

413

Summary of Contents for 2008 Avenger




















































































































































































































































































































































































































































































Search results

Summary of Contents for 2008 Avenger

Reviews:

Related manuals for 2008 Avenger

Brands by name

Popular brands

Dodge 2008 Avenger, Owner'S Manual

Search results

Summary of Contents for 2008 Avenger

Reviews:

Related manuals for 2008 Avenger

Brands by name

Popular brands