manualshive.com logo in svg

Dodge 2008 Avenger, Owner'S Manual

The Dodge 2008 Avenger Owner's Manual is your go-to guide for getting the most out of your vehicle. This comprehensive manual covers everything from maintenance and troubleshooting to important safety information. Download your free copy from manualshive.com and enjoy the peace of mind that comes with knowing your vehicle inside out.

Share
Download
background image

Cleaning Plastic Instrument Cluster Lenses
The lenses in front of the instruments in this vehicle are
molded in clear plastic. When cleaning the lenses, care
must be taken to avoid scratching the plastic.

1. Clean with a wet, soft rag. A mild soap solution may be
used, but do not use high alcohol content or abrasive
cleaners. If soap is used, wipe clean with a clean damp rag.

2. Dry with a soft tissue.

Seat Belt Maintenance
Do not bleach, dye, or clean the belts with chemical
solvents or abrasive cleaners. This will weaken the fabric.
Sun damage can also weaken the fabric.

If the belts need cleaning, use a mild soap solution or
lukewarm water. Do not remove the belts from the car to
wash them.

Replace the belts if they appear frayed or worn or if the
buckles do not work properly.

Dry with a soft tissue.

CLEANING CENTER CONSOLE CUPHOLDERS

Removal
Grab the rubber portion of the cupholder and lift up-
ward.

Cleaning
Soak the rubber cupholder liner in a mixture of medium
hot tap water and one teaspoon of mild liquid dish soap.
Let soak for approximately one hour. After one hour pull
the liner from the water and dip it back into the water
about six times. This will loosen any remaining debris.
Rinse the liner thoroughly under warm running water.
Shake the excess water from the liner and dry the outer
surfaces with a clean soft cloth.

Installation
Align the liner in the cupholder and press down firmly.

MAINTAINING YOUR VEHICLE

405

7

Summary of Contents for 2008 Avenger




















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2008 Avenger

Camcar 40052 Mounting Instructions preview
40052
Brand: Camcar Pages: 6
hager witty park XEV6 Series Installation Manual preview
witty park XEV6 Series
Brand: hager Pages: 9
Vauxhall Meriva Quick Reference Manual preview
Meriva
Brand: Vauxhall Pages: 2
Vauxhall Ampera Quick Reference Manual preview
Ampera
Brand: Vauxhall Pages: 2
Vauxhall 2012 Agila Quick Reference Manual preview
2012 Agila
Brand: Vauxhall Pages: 2
Vauxhall 2013 Mokka Owner'S Manual preview
2013 Mokka
Brand: Vauxhall Pages: 209
VBC Racing WildFire Instruction Manual preview
WildFire
Brand: VBC Racing Pages: 34
Vauxhall 2013 Corsa Infotainment system Quick Reference Manual preview
2013 Corsa Infotainment system
Brand: Vauxhall Pages: 2
Vauxhall 2010 Astra Quick Reference Manual preview
2010 Astra
Brand: Vauxhall Pages: 2
Vauxhall Antara Owner'S Manual preview
Antara
Brand: Vauxhall Pages: 236
Ford 2008 Mustang Quick Reference Manual preview
2008 Mustang
Brand: Ford Pages: 2
Streetwize LeisureWize EMOVE EM303A Manual preview
LeisureWize EMOVE EM303A
Brand: Streetwize Pages: 20
Uebler X21 nano Mounting And Operating Instructions preview
X21 nano
Brand: Uebler Pages: 56
Yakima Prorack K436 Fitting Instructions Manual preview
Prorack K436
Brand: Yakima Pages: 13
Lexus HS 250h Vehicle Dismantling Manual preview
HS 250h
Brand: Lexus Pages: 34
Toyota 86 2020 Quick Reference Manual preview
86 2020
Brand: Toyota Pages: 32
ULTIMATE SPEED 285690 Assembly And Safety Advice preview
285690
Brand: ULTIMATE SPEED Pages: 10
Honda 2009 S2000 Owner'S Manual preview
2009 S2000
Brand: Honda Pages: 268

Brands by name

Popular brands

Load more brands