manualshive.com logo in svg

Dodge 2008 Avenger, Owner'S Manual

The Dodge 2008 Avenger Owner's Manual is your go-to guide for getting the most out of your vehicle. This comprehensive manual covers everything from maintenance and troubleshooting to important safety information. Download your free copy from manualshive.com and enjoy the peace of mind that comes with knowing your vehicle inside out.

Share
Download
background image

humidity accumulating on the radiator and being vapor-
ized when the thermostat opens, allowing hot coolant to
enter the radiator.

If an examination of your engine compartment shows no
evidence of radiator or hose leaks, the vehicle may be
safely driven. The vapor will soon dissipate.

•

Do not overfill the coolant recovery bottle.

•

Check coolant freeze point in the radiator and in the
coolant recovery bottle. If antifreeze needs to be
added, contents of coolant recovery bottle must also be
protected against freezing.

•

If frequent coolant additions are required, or if the
level in the coolant recovery bottle does not drop when
the engine cools, the cooling system should be pres-
sure tested for leaks.

•

Maintain coolant concentration at 50% HOAT engine
coolant (minimum) and distilled water for proper
corrosion protection of your engine, which contains
aluminum components.

•

Make sure that the radiator and coolant recovery
bottle overflow hoses are not kinked or obstructed.

•

Keep the front of the radiator clean. If your vehicle is
equipped with air conditioning, keep the front of the
condenser clean, also.

•

Do not change the thermostat for summer or winter
operation. If replacement is ever necessary, install
ONLY the correct type thermostat. Other designs may
result in unsatisfactory coolant performance, poor gas
mileage, and increased emissions.

MAINTAINING YOUR VEHICLE

393

7

Summary of Contents for 2008 Avenger




















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2008 Avenger

APS Auto Parts Specialist iBoard IB-ZK406 Installation Instructions preview
iBoard IB-ZK406
Brand: APS Auto Parts Specialist Pages: 3
FormFit HD 10L07 Installation Instructions preview
HD 10L07
Brand: FormFit Pages: 2
Phonocar VM350 Mounting Instructions preview
VM350
Brand: Phonocar Pages: 2
Xpresskit DBALL2-HYUNDAI9 Installation And Quick Reference Manual preview
DBALL2-HYUNDAI9
Brand: Xpresskit Pages: 13
RAM 2011 3500 Chassis Cab User Manual preview
2011 3500 Chassis Cab
Brand: RAM Pages: 92
Toro 137-1019 Installation Instructions Manual preview
137-1019
Brand: Toro Pages: 24
Xblitz Mirror 2016 User Manual preview
Mirror 2016
Brand: Xblitz Pages: 30
Menabo DELTA DL FIX 209FP Fitting Instructions Manual preview
DELTA DL FIX 209FP
Brand: Menabo Pages: 8
Nuna Bugaboo turtle Instructions For Installation Manual preview
Bugaboo turtle
Brand: Nuna Pages: 17
Baja Designs 447575 Instructions preview
447575
Brand: Baja Designs Pages: 5
Simplicity 1694286 Installation Instructions Manual preview
1694286
Brand: Simplicity Pages: 10
S&B Filters 75-5053 Installation Instructions preview
75-5053
Brand: S&B Filters Pages: 4
Mazda 2016 CX3 Service Information preview
2016 CX3
Brand: Mazda Pages: 3
Roadmaster 195125 Assembly And Operating Instructions preview
195125
Brand: Roadmaster Pages: 4
ULTIMATE SPEED 290923 Operation And Safety Notes preview
290923
Brand: ULTIMATE SPEED Pages: 56
Soundoff Signal nERGY ETSA200R-PA Quick Start Manual preview
nERGY ETSA200R-PA
Brand: Soundoff Signal Pages: 3
Truma Mover H SE User Manual preview
Mover H SE
Brand: Truma Pages: 10
Blaupunkt 7 608 502 000 Installation Instructions Manual preview
7 608 502 000
Brand: Blaupunkt Pages: 6

Brands by name

Popular brands

Load more brands