manualshive.com logo in svg

Dodge 2008 Avenger, Owner'S Manual

The Dodge 2008 Avenger Owner's Manual is your go-to guide for getting the most out of your vehicle. This comprehensive manual covers everything from maintenance and troubleshooting to important safety information. Download your free copy from manualshive.com and enjoy the peace of mind that comes with knowing your vehicle inside out.

Share
Download
background image

DRIVING THROUGH WATER

Driving through water more than a few inches/
centimeters deep will require extra caution to ensure
safety and prevent damage to your vehicle.

Flowing/Rising Water

WARNING!

Do not drive on, or cross, a road or a path where
water is flowing and/or rising (as in storm run-off).
Flowing water can wear away the road or path’s
surface and cause your vehicle to sink into deeper
water. Furthermore, flowing and/or rising water can
carry your vehicle away swiftly. Failure to follow this
warning may result in injuries that are serious or
fatal to you, your passengers, and others around you.

Shallow Standing Water
Although your vehicle is capable of driving through
shallow standing water, consider the following Caution
and Warning before doing so.

CAUTION!

•

Always check the depth of the standing water
before driving through it. Never drive through
standing water that is deeper than the bottom of
the tire rims mounted on the vehicle.

•

Determine the condition of the road or the path
that is under water, and if there are any obstacles
in the way, before driving through the standing
water.

•

Do not exceed 5 mph (8 km/h) when driving
through standing water. This will minimize wave
effects.

STARTING AND OPERATING

289

5

Summary of Contents for 2008 Avenger




















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2008 Avenger

Daihatsu G200 Service Manual preview
G200
Brand: Daihatsu Pages: 485
cam HS Series Operating Manual preview
HS Series
Brand: cam Pages: 28
Yakima K618 Instructions Manual preview
K618
Brand: Yakima Pages: 11
Safe Fleet PRIME DESIGN VCR 326 Assembly Instructions Manual preview
PRIME DESIGN VCR 326
Brand: Safe Fleet Pages: 16
Safe Fleet Prime Design VBC PC11 Quick Start Manual preview
Prime Design VBC PC11
Brand: Safe Fleet Pages: 8
Safe Fleet Prime Design AR1418 Manual preview
Prime Design AR1418
Brand: Safe Fleet Pages: 4
SnapPad EQ Round Installation Instructions preview
EQ Round
Brand: SnapPad Pages: 5
Sumitomo Dunlop L.D02.C.M Installation Manual preview
Dunlop L.D02.C.M
Brand: Sumitomo Pages: 22
v.link NAL-PC-HSD Manual preview
NAL-PC-HSD
Brand: v.link Pages: 21
GARO Wallbox GLB Quick Start Manual preview
Wallbox GLB
Brand: GARO Pages: 15
travall TDG 1486 Fitting Instructions preview
TDG 1486
Brand: travall Pages: 4
TATA Motors Indigo eCS Owner'S Manual & Service Book preview
Indigo eCS
Brand: TATA Motors Pages: 166
Advanced Diagnostics MVP PRO Manual preview
MVP PRO
Brand: Advanced Diagnostics Pages: 10
Subaru 2015 Forester Quick Reference Manual preview
2015 Forester
Brand: Subaru Pages: 16
Gigaware Gigaware 12-493 User Manual preview
Gigaware 12-493
Brand: Gigaware Pages: 8
Toyota 1998 Celica Owner'S Manual preview
1998 Celica
Brand: Toyota Pages: 204
Gentex Full Display Mirror Installation Instructions Manual preview
Full Display Mirror
Brand: Gentex Pages: 18
Wallbox PLP1 Installation Manual preview
PLP1
Brand: Wallbox Pages: 21

Brands by name

Popular brands

Load more brands