manualshive.com logo in svg

Dodge 2008 Avenger, Owner'S Manual

The Dodge 2008 Avenger Owner's Manual is your go-to guide for getting the most out of your vehicle. This comprehensive manual covers everything from maintenance and troubleshooting to important safety information. Download your free copy from manualshive.com and enjoy the peace of mind that comes with knowing your vehicle inside out.

Share
Download
background image

Keep the blade rubber out of contact with petroleum
products such as engine oil, gasoline, etc.

NOTE:

Always refer to the wiper blade packaging for

specific installation instructions. Many wiper blade re-
placements fit multiple vehicles.

WINDSHIELD WASHERS

NOTE:

Refer to the appropriate “Engine Compartment”

diagram in Section 7 for the location of the windshield
washer fluid reservoir.

The fluid reservoir for the windshield washers is located
in the engine compartment. Be sure to check the fluid
level in the reservoir at regular intervals. Fill the reservoir
with windshield washer solvent (not radiator antifreeze)
and operate the system for a few seconds to flush out the
residual water.

WARNING!

Commercially available windshield washer solvents
are flammable. They could ignite and burn you. Care
must be exercised when filling or working around
the washer solution.

EXHAUST SYSTEM

The best protection against carbon monoxide entry into
the vehicle body is a properly maintained engine exhaust
system.

If you notice a change in the sound of the exhaust system
or if exhaust fumes can be detected inside the vehicle or
when the underside or rear of the vehicle is damaged,
have a competent technician inspect the complete ex-
haust system and adjacent body areas for broken, dam-
aged, deteriorated, or mispositioned parts. Open seams
or loose connections could permit exhaust fumes to seep

MAINTAINING YOUR VEHICLE

387

7

Summary of Contents for 2008 Avenger




















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2008 Avenger

VEAP SHIELD UNITED FT Series Mounting Instruction preview
FT Series
Brand: VEAP SHIELD UNITED Pages: 3
Ignition 63-231 Quick Start preview
63-231
Brand: Ignition Pages: 1
Waeco MagicWatch MWE800 Installation And Operating Manual preview
MagicWatch MWE800
Brand: Waeco Pages: 212
CITROEN PICASSO XSARA DESIRE 1.6 - MESUREMENT Manual preview
PICASSO XSARA DESIRE 1.6 - MESUREMENT
Brand: CITROEN Pages: 2
I.D. Systems Vehicle Asset Communicator User Manual preview
Vehicle Asset Communicator
Brand: I.D. Systems Pages: 41
Warn 70948 Installation Instructions preview
70948
Brand: Warn Pages: 5
Calix group TYP MVP 823 Assembly Instructions preview
TYP MVP 823
Brand: Calix group Pages: 4
Wagan Easy Air Auto Screen User Manual preview
Easy Air Auto Screen
Brand: Wagan Pages: 8
N-Com Bluetooth Kit3 PLUS User Instructions And Safety preview
Bluetooth Kit3 PLUS
Brand: N-Com Pages: 36
Safe Fleet Prime Design VBI-FT31B Assembly Instructions Manual preview
Prime Design VBI-FT31B
Brand: Safe Fleet Pages: 12
Yakima K1198 Instructions Manual preview
K1198
Brand: Yakima Pages: 10
AA Products APX2501 BLK Instruction Manual preview
APX2501 BLK
Brand: AA Products Pages: 8
Thermo King V-520 RT Series Installation Manual preview
V-520 RT Series
Brand: Thermo King Pages: 56
AL-KO 605 363 Operating Instructions Manual preview
605 363
Brand: AL-KO Pages: 88
Prorack K890 Fitting Instructions Manual preview
K890
Brand: Prorack Pages: 15
Prorack K129 Fitting Instructions Manual preview
K129
Brand: Prorack Pages: 13
Enduro EM303 User Manual preview
EM303
Brand: Enduro Pages: 56
SAF-HOLLAND SK-V 20 Mounting, Operation And Maintenance preview
SK-V 20
Brand: SAF-HOLLAND Pages: 22

Brands by name

Popular brands

Load more brands