Dodge 2008 Avenger Owner'S Manual Download Page 361 | Manualshive

Page: 361 / 467

background image

1. Wear eye protection and remove any metal jewelry
such as watchbands or bracelets that might make an
inadvertent electrical contact.

2. When boosting from a battery in another vehicle, park
that vehicle within booster cable reach, but without
allowing the vehicles to touch. Set parking brake, place
automatic transaxle in PARK and turn ignition to LOCK
for both vehicles.

WARNING!

Do not permit vehicles to touch each other as this
could establish a ground connection and personal
injury could result.

3. Turn off the heater, radio, and all unnecessary electri-
cal loads.

4. Remove the protective cover over the remote jump-
start positive battery post (+) in the engine compartment.
Connect one end of the jumper cable to the positive
battery post. Connect the other end of the same cable to
the positive terminal of the booster battery. Refer to the
following illustration for jump-starting connections.

Jump-Starting Location

WHAT TO DO IN EMERGENCIES

359

6

«
...
359
360
361
362
363
...
»

Summary of Contents for 2008 Avenger




















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2008 Avenger

Brand: Vauxhall Pages: 2

Brand: Ultra Start Pages: 8

Brand: Vauxhall Pages: 199

Brand: Porsche Pages: 51

Brand: Whispbar Pages: 14

Brand: BESAFE Pages: 4

2008 MX-5 Miata

Brand: Mazda Pages: 400

Automotive 31006

Brand: KRAFTWERK Pages: 2

Brand: Audiovox Pages: 24

Brand: Mercedes-Benz Pages: 2

Brand: Westin Pages: 2

Brand: SAN HIMA Pages: 7

Peterbilt SmartAir

Brand: Paccar Pages: 58

Brand: Mercedes-Benz Pages: 153

Brand: Ford Pages: 8

Brand: Intec Pages: 16

Brand: Vauxhall Pages: 131

Brand: Yakima Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands