manualshive.com logo in svg

Dodge 2008 Avenger, Owner'S Manual

The Dodge 2008 Avenger Owner's Manual is your go-to guide for getting the most out of your vehicle. This comprehensive manual covers everything from maintenance and troubleshooting to important safety information. Download your free copy from manualshive.com and enjoy the peace of mind that comes with knowing your vehicle inside out.

Share
Download
background image

•

Trailer brakes are recommended for trailers over 1,000
lbs (450 kg) and required for trailers in excess of 2,000
lbs (907 kg).

CAUTION!

If the trailer weighs more than 1,000 lbs (450 kg)
loaded, it should have its own brakes with adequate
braking capacity. Failure to do this could lead to
accelerated brake lining wear, higher brake pedal
effort, and longer stopping distances.

WARNING!

Do not connect trailer brakes to your vehicle’s hy-
draulic brake lines. It can overload your brake sys-
tem and cause it to fail. You might not have brakes
when you need them and could have an accident.

Towing any trailer will increase your stopping dis-
tance. When towing, you should allow for additional
space between your vehicle and the vehicle in front
of you. Failure to do so could result in an accident.

Towing Requirements — Trailer Lights and Wiring
Whenever you pull a trailer, regardless of the trailer size,
stoplights and turn signals on the trailer are required for
motoring safety.

Use a factory approved trailer harness and connector.

342

STARTING AND OPERATING

Summary of Contents for 2008 Avenger




















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2008 Avenger

ZAPTEC Go Quick Manual preview
Go
Brand: ZAPTEC Pages: 64
ZAPTEC Go Installation Manual preview
Go
Brand: ZAPTEC Pages: 24
JANE MICRO Quick Start Manual preview
MICRO
Brand: JANE Pages: 6
Laser 4832 Manual preview
4832
Brand: Laser Pages: 8
IAME Parilla X30 Assembly Instructions And User'S Manual preview
Parilla X30
Brand: IAME Pages: 17
iDataLink ADS-ALCA Install Manuals preview
ADS-ALCA
Brand: iDataLink Pages: 30
OEM Audio Reference Series Manual preview
Reference Series
Brand: OEM Audio Pages: 29
Taffio CH7102-FCX9 Quick Start Manual preview
CH7102-FCX9
Brand: Taffio Pages: 8
Ford F-150 2018 Quick Reference Manual preview
F-150 2018
Brand: Ford Pages: 12
Horn Tools HISDMSPTRA01 Mounting Instructions preview
HISDMSPTRA01
Brand: Horn Tools Pages: 6
Mercedes-Benz R-Class Owner'S Manual preview
R-Class
Brand: Mercedes-Benz Pages: 373
AutoWatch 457 Rli Wiring Diagram preview
457 Rli
Brand: AutoWatch Pages: 4
Valeo Park Vision VAL632210 Instruction Manual preview
Park Vision VAL632210
Brand: Valeo Pages: 25
Cadillac STS 2011 Owner'S Manual preview
STS 2011
Brand: Cadillac Pages: 529
Toro 07389 Installation Instructions Manual preview
07389
Brand: Toro Pages: 16
Whispbar K684W Fitting Instructions Manual preview
K684W
Brand: Whispbar Pages: 15
MBRP 0130717 Assembly preview
0130717
Brand: MBRP Pages: 5
Acura 08L03-TA1-200A Installation Instructions preview
08L03-TA1-200A
Brand: Acura Pages: 4

Brands by name

Popular brands

Load more brands